Check the gap (C) and flush (D) between the roof panel (A) and the glass (B).
Front roof panel (A) - glass (B)
Gap (C) (mm)
Flush (D) (mm)
5.2 ± 0.4
-1 - 0
Glass (B) - rear roof panel (A)
Gap (C) (mm)
Flush (D) (mm)
5.2 ± 0.4
0 - 1
If necessary to adjust the glass (A), glass height adjustment screw (B) loosen slightly and then tighten up tightening torque. Tightening torque : 2 - 3,9 N·m (0.2 - 0.4 kgf·m, 1.4 - 2.9 lb·ft, 17.4 - 34.7 lb·in)
Initialize Sunroof If the glass does not move automatically when the switch is operated with one touch or emergency operation (manual operation) is performed, the sunroof must be initialized as follows.
In the following cases, the initial value of the sunroof motor has been erased. Perform initialization.
When the power of the battery connected to the sunroof motor is cut off due to battery replacement, discharge, or fuse replacement
When the one-touch function AUTO open and AUTO close do not work normally.
During the AUTO closing operation, if the glass opens without object stuck in the sunroof (safety specification).
After IG ON, completely close the glass using the sunroof close switch.
When the glass is completely closed, release the sunroof close switch and press the closing switch again until the glass moves slightly (about 10 seconds).
If you release your hand from the sunroof close switch and press it again, the glass tilts and slides open and then closes, completing the sunroof initialization.
During the above operation, if the glass close button is released and the operation is stopped, the initialization is not completed and must return to step.
Emergency operation of the sunroof must not be performed except when the sunroof must be closed or opened in a state where the motor is faulty.
After removing the roof trim, use a hexagon wrench to close or open the sunroof, and do not apply excessive force. [Moving Glass Motor] [Roller Blind Motor]
In case of emergency operation of the sunroof, initialize the sunroof for normal sunroof operation.
Emergency Operation
Sunroof Glass Removal and Installation
Removal
Press the sunroof switch to tilt the sunroof glass.
Remove the sunroof glass (A) after removing the screws (B).
Remove the sunroof glass weatherstrip (A).
Installation
Install in reverse order of removal.
After installing the sunroof glass, adjust the glass.
Sunroof Deflector Removal and Installation
Removal
Press the sunroof switch to fully open the sunroof glass.
Remove the sunroof protector (A).
Remove the spring (A) after removing the hook (B).
Separate the sunroof deflector guide (A) in the direction of the arrow.
Remove the sunroof deflector guide (A) in the direction of the arrow.
Installation
Install in reverse order of removal.
Sunroof Motor Removal and Installation
Removal
Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
Remove the sunroof motor connector (A).
Remove the sunroof motor (A) after removing the screws.
Installation
Install in reverse order of removal.
Check the operation of the sunroof and initialize the sunroof in case of malfunction.
Sunroof Assembly Removal and Installation
Removal
Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
Remove the drain hoses (A) after releasing the hose clamps (B).
Remove the sunroof assembly (A) after removing the nuts. Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
Installation
Install in reverse order of removal.
Check the operation of the sunroof and initialize the sunroof in case of malfunction.
Sunroof Sunshade Removal and Installation
Removal
Remove the sunroof assembly. (Refer to Sunroof - "Sunroof Assembly")
Remove the rear drip screw (A).
Open the rear drip (A) in the direction of the arrow.
Remove the sunshade stopper (A).
Remove the sunroof sunshade (A) in the direction of the arrow.
Installation
Install in reverse order of removal.
Sunroof Guide Removal and Installation
Removal
Remove the sunroof sunshade. (Refer to Sunroof - "Sunroof Sunshade")
Remove the drip rail hook (A) in the direction of the arrow.
Remove the drip rail guide (A) in the direction of the arrow.
Remove the drip rail (A).
Remove the sunroof guide and drip link (A) in the direction of the arrow.
Separate the drip link (A) and the sunroof guide (B).
Remove the roller shoe (A).
Remove the cable assembly (A) in the direction of the arrow.