Transmission & Driveline

P0705 Transmission Range Sensor a

35steps
~210min
4/5difficulty
Done 0 of 35
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0705

T/M RANGE SENSOR A

[Transmission Range Sensor A Circuit (PRNDL Input)]
Diagnosis condition TCM power supply voltage: More than 11 V
Signal Transmision range switch signal
Threshold Two or more range signals simultaneously stay ON continuously
Diagnosis delay time Maintained for 2 seconds

POSSIBLE CAUSE

  • Harness or connector (Short circuit between transmission range switch and TCM)

  • Transmission range switch

FAIL-SAFE

  • Shift position indicator on combination meter is not displayed

  • Selector shock is large

  • Start is slow

  • Acceleration is slow

  • Lock-up is not performed

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 2.

CHECK DTC DETECTION

  1. Turn ignition switch ON.

  2. Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for 5 seconds or more.)

  3. Check the first trip DTC.

Is “P0705” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK TCM INPUT SIGNALS

With CONSULT

  1. Turn ignition switch ON.

  2. Select “Data Monitor” in “TRANSMISSION”.

  3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, and “P POSITION SW”.

  4. Shift the selector lever through entire positions from “P” to “D” and check ON/OFF of each monitor item.

    Monitor itemTest conditionCondition
    D POSITION SW Selector lever: “D” position On
    Other than the above Off
    N POSITION SW Selector lever: “N” position On
    Other than the above Off
    R POSITION SW Selector lever: “R” position On
    Other than the above Off
    P POSITION SW Selector lever: “P” position On
    Other than the above Off

Without CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Turn ignition switch ON.

  4. Shift the selector lever from “P” to “D” and check voltage between TCM harness connector terminals and ground.

    +−Test conditionVoltage
    TCM
    ConnectorTerminal
    F25 4 Ground Selector lever: “D” position 10 – 16 V
    Other than the above Approx. 0 V
    5 Selector lever: “N” position 10 – 16 V
    Other than the above Approx. 0 V
    6 Selector lever: “R” position 10 – 16 V
    Other than the above Approx. 0 V
    7 Selector lever: “P” position 10 – 16 V
    Other than the above Approx. 0 V

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO-1>>

“D POSITION SW” is “ON” when selector is not in “D” position Or connector terminal 4 is at power voltage: GO TO 2.

NO-2>>

“N POSITION SW” is “ON” when selector is not in “N” position Or connector terminal 5 is at power voltage: GO TO 4.

NO-3>>

“R POSITION SW” is “ON” when selector is not in “R” position Or connector terminal 6 is at power voltage: GO TO 8.

NO-4>>

“P POSITION SW” is “ON” when selector is not in “P” position Or connector terminal 7 is at power voltage: GO TO 6.

CHECK D POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between TCM harness connector terminals.

    TCMContinuity
    ConnectorTerminal
    F25 4 2 Not existed
    5
    6
    7

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning parts.

CHECK D POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.

  2. Turn ignition switch ON.

  3. Check voltage between TCM harness connector terminal and ground.

    +−

    Voltage

    (Approx.)
    TCM
    ConnectorTerminal
    F25 4 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace malfunctioning parts.

CHECK N POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between TCM harness connector terminals.

    TCMContinuity
    ConnectorTerminal
    F25 5 2 Not existed
    4
    6
    7

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning parts.

CHECK N POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.

  2. Turn ignition switch ON.

  3. Check voltage between TCM harness connector terminal and ground.

    +−

    Voltage

    (Approx.)
    TCM
    ConnectorTerminal
    F25 5 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace malfunctioning parts.

CHECK P POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between TCM harness connector terminals.

    TCMContinuity
    ConnectorTerminal
    F25 7 2 Not existed
    4
    5
    6

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace malfunctioning parts.

CHECK P POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.

  2. Turn ignition switch ON.

  3. Check voltage between TCM harness connector terminal and ground.

    +−

    Voltage

    (Approx.)
    TCM
    ConnectorTerminal
    F25 7 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace malfunctioning parts.

CHECK R POSITION SW CIRCUIT (PART1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between TCM harness connector terminals.

    TCMContinuity
    ConnectorTerminal
    F25 6 2 Not existed
    4
    5
    7

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace malfunctioning parts.

CHECK R POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.

  2. Turn ignition switch ON.

  3. Check voltage between TCM harness connector terminal and ground.

    +−

    Voltage

    (Approx.)
    TCM
    ConnectorTerminal
    F25 6 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to Component Inspection.

Is the check result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace transmission range switch. Refer to Removal and Installation.

Component Inspection

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Transmission range switchConditionContinuity
Terminal
7 – 10 Manual lever: “P” and “N” positions Existed
Other than the above Not existed
4 – 5 Manual lever: “P” position Existed
Other than the above Not existed
4 – 8 Manual lever: “R” position Existed
Other than the above Not existed
4 – 9 Manual lever: “N position Existed
Other than the above Not existed
4 – 2 Manual lever: “D” position Existed
Other than the above Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

There is malfunction of transmission range switch. Replace transmission range switch. Refer to Removal and Installation.