P0826 up and Down Shift Sw
DTC DETECTION LOGIC
| DTC | CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | |
| P0826 | UP/DOWN SHIFT SWITCH (Up and Down Shift Switch Circuit) |
Diagnosis condition | Engine is started |
| Signal | — | ||
| Threshold | TCM monitors manual mode, non-manual mode, up or down switch signal, and detects as irregular when impossible input pattern occurs | ||
| Diagnosis delay time | 1 second or more | ||
POSSIBLE CAUSE
Manual mode switch
Harness or connectors
(Manual mode switch circuit are open or shorted.)
FAIL-SAFE
Manual mode is not activated
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>>GO TO 2.
CHECK DTC DETECTION (PART 1)
With CONSULT
Start the engine.
Shift the selector lever to “D” position and wait for 1 second or more.
Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0826” detected?
YES>>Go to Diagnosis Procedure.
NO>>GO TO 3.
CHECK DTC DETECTION (PART 2)
With CONSULT
Shift the selector lever to manual shift gate and wait for 1 second or more.
Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0826” detected?
YES>>Go to Diagnosis Procedure.
NO>>GO TO 4.
CHECK DTC DETECTION (PART 3)
With CONSULT
Shift the selector lever to “UP side (+ side)” and wait for 1 second or more.
Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0826” detected?
YES>>Go to Diagnosis Procedure.
NO>>GO TO 5.
CHECK DTC DETECTION (PART 4)
With CONSULT
Shift the selector lever to “DOWN side (− side)” and wait for 1 second or more.
Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0826” detected?
YES>>Go to Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
CHECK DTC (COMBINATION METER)
With CONSULT
Turn ignition switch ON.
Select “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES>>Check DTC detected item. Refer to DTC Index.
NO>>GO TO 2.
CHECK MANUAL MODE SWITCH POWER SUPPLY CIRCUIT
Turn ignition switch OFF.
Disconnect CVT shift selector connector.
Turn ignition switch ON.
Check voltage between CVT shift selector harness connector terminal and ground.
+ – Condition Voltage
(Approx.)CVT shift selector Connector Terminal M78 7 Ground Ignition switch: ON 12 V Ignition switch: OFF 0 V 8 Ignition switch: ON 12 V Ignition switch: OFF 0 V 9 Ignition switch: ON 12 V Ignition switch: OFF 0 V 10 Ignition switch: ON 12 V Ignition switch: OFF 0 V
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 4.
CHECK MANUAL MODE SWITCH
Turn ignition switch OFF.
Check manual mode switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace damaged parts.
CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER
Turn ignition switch OFF.
Disconnect combination meter connector.
Check continuity between CVT shift selector harness connector terminals and combination meter harness connector terminals.
CVT shift selector Combination meter Continuity Connector Terminal Connector Terminal M78 7 M23 30 Existed 8 33 9 32 10 31 Check continuity between CVT shift selector harness connector terminals and ground.
CVT shift selector — Continuity Connector Terminal M78 7 Ground Not existed 8 9 10
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Repair or replace damaged parts.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
| CVT shift selector | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M78 | 11 | Ground | Existed |
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Repair or replace damaged parts.
MANUAL MODE SWITCH
Check continuity between CVT shift selector connector terminals.
| CVT shift selector | Condition | Continuity |
|---|---|---|
| Terminal | ||
| 7 – 11 | Manual shift gate position (neutral) | Existed |
| Other than the above | Not existed | |
| 8 – 11 | Selector lever: DOWN (− side) | Existed |
| Other than the above | Not existed | |
| 9 – 11 | Selector lever: UP (+ side) | Existed |
| Other than the above | Not existed | |
| 10 – 11 | Manual shift gate position | Not existed |
| Other than the above | Existed |
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace the CVT shift selector assembly due to malfunction in manual mode switch. Refer to Removal and Installation.