Transmission & Driveline

P0715 Input Speed Sensor a

16steps
~96min
4/5difficulty
Done 0 of 16
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0715

INPUT SPEED SENSOR A

(Input/Turbine Speed Sensor “A” Circuit)
Diagnosis condition

When the following conditions are satisfied:

  • TCM power supply voltage: More than 11 V

  • After range change completion, it spends 2 seconds or more.

  • Range: Other than P, N

  • P0791, P0792, and P0793 are not detected

Signal —
Threshold

When the following conditions are satisfied:

  • Primary pulley speed: 500 rpm or more

  • Input speed: Less than 150 rpm

Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Harness or connector (Input speed sensor circuit is open or shorted)

  • Input speed sensor

FAIL-SAFE

  • Start is slow

  • Acceleration is slow

  • Lock-up is not performed

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Start the engine.

  2. Drive the Nissan Murano vehicle.

  3. Maintain the following conditions for 10 seconds or more.

    Selector lever : “D” position
    Engine speed : 1,200 rpm or more
    Nissan Murano Vehicle speed : 40 km/h or more
  4. Stop the vehicle.

  5. Check the first trip DTC.

Is “P0715” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK INPUT SPEED SENSOR POWER CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect input speed sensor connector.

  3. Turn ignition switch ON.

  4. Check voltage between input speed sensor harness connector terminal and ground.

    +−Voltage
    Input speed sensor
    ConnectorTerminal
    F37 3 Ground 10 – 16 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 6.

CHECK INPUT SPEED SENSOR GROUND CIRCUIT

Check continuity between input speed sensor harness connector terminal and ground.

Input speed sensor—Continuity
ConnectorTerminal
F37 1 Ground Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between input speed sensor harness connector terminal and TCM harness connector terminal.

    Input speed sensorTCMContinuity
    ConnectorTerminalConnectorTerminal
    F37 2 F25 24 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between input speed sensor harness connector terminal and ground.

Input speed sensor—Continuity
ConnectorTerminal
F37 2 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning parts.

CHECK TCM INPUT SIGNALS

  1. Connect all of disconnected connectors.

  2. Lift the Nissan Murano vehicle.

  3. Start the engine.

  4. Check frequency of input speed sensor.

    +−Condition

    Frequency

    (Approx.)
    TCM
    ConnectorTerminal
    F25 24 Ground
    • Selector lever: “M1” position

    • Nissan Murano Vehicle speed: 20 km/h

    800 Hz

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace input speed sensor. Refer to Removal and Installation.

DETECT MALFUNCTIONING ITEMS

Check the following items:

  • Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to Wiring Diagram.

  • Harness open circuit or short circuit between IPDM E/R connector terminal 61 and input speed sensor connector terminal 3.

  • 10A fuse (No.43, located in the IPDM E/R). Refer to IPDM E/R Terminal Arrangement .

  • IPDM E/R

Is the check result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace malfunctioning parts.