Transmission & Driveline

P0711 Transmission Fluid Temperature Sensor a

42steps
~252min
5/5difficulty
Done 0 of 42
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0711

FLUID TEMP SENSOR A

(Transmission Fluid Temperature Sensor A Circuit Range/Performance)
1 Diagnosis condition

When all of the following conditions are satisfied.

  • TCM power supply voltage: More than 11 V

  • CAN communication is normal

  • Engine speed: 450 rpm or more

  • Accelerator pedal position: 3 deg. or more

  • Nissan Murano Vehicle speed: 10 km/h or more

  • U0100, P0705 and P0706 are not detected.

  • Selector lever: “D” position

Signal CVT fluid temperature sensor signal
Threshold CVT fluid temperature does not rise to 10 °C after driving for a certain period of time with the TCM-received fluid temperature sensor value between − 40 °C and 9 °C.
Diagnosis delay time —
2 Diagnosis condition

All of the following conditions are satisfied within 2 seconds after the ignition switch is turned ON.

  • U0073, U0100, P0712 and P0713 are not detected.

  • CAN communication is normal.

  • TCM power supply voltage: More than 11 V

  • The difference between CVT fluid temperature and engine coolant temperature is 55 °C or more, or −27 °C or less.

Signal CVT fluid temperature sensor signal
Threshold

When all of the following conditions are satisfied

  • ECM is normal.

  • Diagnosis condition is satisfied.

Diagnosis delay time Maintained for 300 seconds

POSSIBLE CAUSE

CVT fluid temperature sensor

FAIL-SAFE

  • Engine coolant temperature when engine start: Temp. ≥ 10 °C

    • Start is slow

    • Acceleration is slow

  • Engine coolant temperature when engine start: −35 °C ≤ Temp. < 10 °C

    • Selector shock is large

    • Start is slow

    • Acceleration is slow

  • Engine coolant temperature when engine start: Temp. <−35 °C

    • Selector shock is large

    • Start is slow

    • Acceleration is slow

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 2.

INSPECTION START

Is it necessary to erase permanent DTC?

YES>>

GO TO 3.

NO>>

GO TO 7.

CHECK DTC (ECM AND TCM)

Check the DTC.

Is any DTC other than “P0711” detected?

YES>>

Check DTC detected item. Refer to DTC Index (ECM), DTC Index (TCM).

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE (PART 1)

TESTING CONDITION:

  • While performing the following procedure, do not add fuel.

  • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.

  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

With CONSULT

  1. Move the Nissan Murano vehicle to a cool place.

  2. Turn ignition switch OFF and leave the Nissan Murano vehicle for 12 hours.

  3. Turn ignition switch ON.

  4. Select “Data Monitor” in “TRANSMISSION”.

  5. Select “FLUID TEMP”.

  6. Record CVT fluid temperature.

  7. Start engine and let it idle for 5 minutes or more.

  8. Check 1st trip DTC.

With GST

  1. Move the Nissan Murano vehicle to a cool place.

  2. Turn ignition switch OFF and leave the Nissan Murano vehicle for 12 hours.

  3. Start engine and let it idle for 5 minutes or more.

  4. Check 1st trip DTC.

Is “P0711” detected?

YES>>

Go to Diagnosis Procedure.

NO-1 >>

With CONSULT: GO TO 5.

NO-2>>

With GST: GO TO 6.

CHECK CVT FLUID TEMPERATURE

With CONSULT

  1. Select “Data Monitor” in “TRANSMISSION”.

  2. Select “FLUID TEMP”.

Is the value of “FLUID TEMP” 10 °C or more?

YES>>

INSPECTION END

NO>>

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE (PART 2)

With CONSULT

  1. Drive the Nissan Murano vehicle for the total minutes specified in the Driving time column below with the following conditions satisfied.

    Selector lever : “D” position
    Accelerator pedal position : 1.0/8 or more
    Nissan Murano Vehicle speed : 10 km/h or more
    CVT fluid temperature before engine startDriving time
    −40 °C –−31 °C 20 minutes or more
    −30 °C –−21 °C 18 minutes or more
    −20 °C –−11 °C 14 minutes or more
    −10 °C –−1 °C 10 minutes or more
    0 °C – 9 °C 7 minutes or more
  2. Stop the Nissan Murano vehicle.

  3. Check the first trip DTC.

With GST

  1. Drive the Nissan Murano vehicle and maintain the following conditions for 20 minutes or more.

    Selector lever : “D” position
    Accelerator pedal position : 1.0/8 or more
    Nissan Murano Vehicle speed : 10 km/h or more
  2. Stop the vehicle.

  3. Check the first trip DTC.

Is “P0711” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch OFF and cool the engine.

  2. Turn ignition switch ON.

  3. Select “Data Monitor” in “TRANSMISSION”.

  4. Select “FLUID TEMP”.

  5. Record CVT fluid temperature.

  6. Start the engine and wait for at least 2 minutes.

  7. Drive the Nissan Murano vehicle for the total minutes specified in the Driving time column below with the following conditions satisfied.

    Selector lever : “D” position
    Accelerator pedal position : 1.0/8 or more
    Nissan Murano Vehicle speed : 10 km/h or more
    CVT fluid temperature before engine startDriving time
    −40 °C –−31 °C 20 minutes or more
    −30 °C –−21 °C 18 minutes or more
    −20 °C –−11 °C 14 minutes or more
    −10 °C –−1 °C 10 minutes or more
    0 °C – 9 °C 7 minutes or more
    Other than the above — (Go to “8.CHECK CVT FLUID TEMPERATURE SENSOR”)
  8. Stop the Nissan Murano vehicle.

  9. Check the first trip DTC.

With GST

  1. Turn ignition switch OFF and cool the engine.

  2. Start the engine and wait for at least 2 minutes.

  3. Drive the Nissan Murano vehicle and maintain the following conditions for 20 minutes or more.

    Selector lever : “D” position
    Accelerator pedal position : 1.0/8 or more
    Nissan Murano Vehicle speed : 10 km/h or more
  4. Stop the vehicle.

  5. Check the first trip DTC.

Is “P0711” detected?

YES>>

Go to Diagnosis Procedure.

NO>>

GO TO 8.

CHECK CVT FLUID TEMPERATURE SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect CVT unit connector.

  3. Check resistance between CVT unit connector terminals.

    CVT unitCondition

    Resistance

    (Approx.)
    Terminal
    12 – 18 CVT fluid temperature: 20 °C 6.5 kΩ
    CVT fluid temperature: 50 °C 2.2 kΩ
    CVT fluid temperature: 80 °C 0.87 kΩ

Is the inspection result normal?

YES>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES>>

Confirmation after repair: INSPECTION END

NO>>

There is a malfunction of CVT fluid temperature sensor. Replace terminal cord assembly. Refer to Removal and Installation.

Diagnosis Procedure

CHECK CVT FLUID TEMPERATURE SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect CVT unit connector.

  3. Check resistance between CVT unit connector terminals.

    CVT unitCondition

    Resistance

    (Approx.)
    ConnectorTerminal
    F210 12 – 18 CVT fluid temperature: 20 °C 6.5 kΩ
    CVT fluid temperature: 50 °C 2.2 kΩ
    CVT fluid temperature: 80 °C 0.87 kΩ

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace terminal cord assembly. Refer to Removal and Installation.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)

  1. Disconnect the TCM connector.

  2. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.

    TCMCVT unitContinuity
    ConnectorTerminalConnectorTerminal
    F25 11 F44 18 Existed
    12 12

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace damaged parts.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)

Check continuity between TCM harness connector terminals and ground.

TCM—Continuity
ConnectorTerminal
F25 11 Ground Not existed
12

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace damaged parts.