Transmission & Driveline

Shift Lock System

9steps
~54min
3/5difficulty
Done 0 of 9
Component Function Check

CHECK SHIFT LOCK OPERATION (PART 1)

  1. Ignition switch ON.

  2. Shift the selector lever to “P” (Park) position.

  3. Attempt to shift the selector lever to any other position with the brake pedal released.

Can the selector lever be shifted to any other position?

YES>>

Refer to Diagnosis Procedure.

NO>>

GO TO 2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other position with the brake pedal depressed.

Can the selector lever be shifted to any other position?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK POWER SOURCE

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check voltage between BCM harness connector and ground while pressing the brake pedal.

    (+)(–)Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M18 27 Ground Brake pedal depressed Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK STOP LAMPS

Do the stop lamps operate normally?

Is the inspection result normal?

YES>>

Check the following:

  • Harness between fuse block (J/B) and BCM.

  • Fuse block (J/B).

NO>>

Refer to Wiring Diagram.

CHECK HARNESS BETWEEN BCM AND CVT SHIFT SELECTOR

  1. Disconnect CVT shift selector connector.

  2. Check continuity between BCM harness connector and CVT shift selector harness connector.

    BCMCVT shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    M80 108 M78 3 Yes
  3. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    M80 108 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness or connector.

CHECK GROUND CIRCUIT (CVT SHIFT SELECTOR)

Check continuity between CVT shift selector harness connector and ground.

CVT shift selector—Continuity
ConnectorTerminal
M78 4 Ground Yes

Is the inspection result normal?

YES>>

Replace CVT shift selector. Refer to Removal and Installation.

NO>>

Repair or replace harness or connector.

Component Inspection (Shift Lock Solenoid)

CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid and park position switch connector and check that shift lock solenoid is activated.

(+) (fuse)(–)ConditionStatus
CVT shift selector
Terminals
3 4 Apply 12 V between terminals 3 and 4 with the park position switch in the "P" (park) position. Shift lock solenoid operates

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace CVT shift selector. Refer to Removal and Installation.

Component Inspection (Park Position Switch)

CHECK PARK POSITION SWITCH

Apply voltage to terminals of shift lock solenoid and park position switch connector and check that shift lock solenoid is activated.

(+) (fuse)(–)ConditionStatus
CVT shift selector
Terminals
3 4 Apply 12 V between terminals 3 and 4 with the park position switch in the "P" (park) position. Shift lock solenoid operates

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace CVT shift selector. Refer to Removal and Installation.

Component Inspection (Stop Lamp Switch)

CHECK STOP LAMP SWITCH

Check the continuity between the stop lamp switch connector terminals.

Stop lamp switchConditionContinuity
Terminals
1 2 Depressed brake pedal Yes
Released brake pedal No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp switch. Refer to Exploded View.