Transmission & Driveline

P0965 Pressure Control Solenoid B

9steps
~54min
3/5difficulty
Done 0 of 9
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0965

PC SOLENOID B

(Pressure Control Solenoid B Control Circuit Range Performance)
1 Diagnosis condition

When all of the following conditions are satisfied:

  • DTC other than the applicable DTC is not detected.

  • Engine speed: More than 625 rpm

  • Selector lever: Other than P/N position

  • CVT fluid temperature: More than -20°C (-4°F)

  • TCM power supply: More than 11 V

  • The difference between instruction pressure of primary pressure and 10-msec-ago instruction primary pressure is 0 MPa or more

  • Instruction pressure of primary pressure: 0.86 MPa or more

  • Instruction pressure of primary pressure - primary pressure: More than 1.2 MPa

Signal —
Threshold

When all of the following conditions are satisfied and this state is maintained for 1 second:

  • Instruction pressure of primary pressure: More than 2 MPa

  • Primary pressure: 0.4 MPa or less

Diagnosis delay time Maintained for 10 seconds
2 Diagnosis condition

When all of the following conditions are satisfied:

  • DTC other than the applicable DTC is not detected.

  • CVT fluid temperature: More than -20°C (-4°F)

  • Selector lever: Other than P/N position

  • TCM power supply: More than 11 V

  • The difference between instruction pressure of primary pressure and 10-msec-ago instruction primary pressure is 0 MPa or more

  • Primary pressure - instruction pressure of primary pressure: More than 1.2 MPa

Signal —
Threshold

When all of the following conditions are satisfied and this state is maintained for 5.5 seconds:

  • Primary pressure - instruction pressure of primary pressure: 1.2 MPa or more

Diagnosis delay time Maintained for 10 seconds

POSSIBLE CAUSE

  • Harness or connector (Primary pressure solenoid valve circuit is open or shorted)

  • Primary pressure solenoid valve

FAIL-SAFE

  • When a malfunction occurs on the low oil pressure side

    • Selector shock is large

    • Start is slow

    • Acceleration is slow

    • Lock-up is not performed

  • When a malfunction occurs on the high oil pressure side

    • Selector shock is large

    • Lock-up is not performed

DTC Confirmation Procedure

CHECK DTC PRIORITY

When DTC P0965 is displayed together with P17F0, diagnose first the P17F0.

Is "P17F0" detected?

YES>>

Perform diagnosis of P17F0. Refer to Diagnosis Procedure.

NO>>

GO TO 2.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 3.

CHECK DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Murano vehicle.

  3. Maintain the following conditions for 20 seconds or more.

    Nissan Murano Vehicle speed : 40 km/h or more
  4. Stop the vehicle.

  5. Check the first trip DTC.

Is “P0965”detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CVT CHAIN

Inspect the CVT chain. Refer to Component Inspection.

Is CVT chain OK?

YES>>

GO TO 2.

NO>>

GO TO 3.

INSTALL NEW CONTROL VALVE

Install new control valve. Refer to Removal and Installation.

>>

WORK END

REPLACE SUB-ASSEMBLY AND INSTALL NEW CONTROL VALVE

Replace sub-assembly and install new control valve. Refer to Disassembly & Assembly.

>>

WORK END

Component Inspection

CVT CHAIN BELT INSPECTION

  • Place the transmission gear selector in Neutral.

  • Leave the driver door unlatched.

  1. Remove the control valve. Refer to Removal and Installation.

  2. Secure the right front tire with a suitable strap . This will assist in making the chain belt turn.

  3. Mark the left front tire with a suitable marking. This will ensure all 360° of the chain belt is inspected.

  4. Using borescope J-51951 with mirror attachment, visually inspect the entirety of the two sides of the chain belt that come in contact with the pulleys . Slowly and carefully turn the left front tire one full turn in the forward rotation to view all of the chain belt.

    Guide rail
    : Front
    1. Route the camera cable past the primary pulley and position the camera lens behind the plastic guide. See figure below.

      Chain belt Camera cable Secondary pulley
      Plastic guide Primary pulley : Front
    2. First inspect the entire 360° of the driver side of the chain belt that comes in contact with the pulley. Refer to figures below for examples of normal and excessive wear patterns.

      Pulley
      Guide rail
      Camera flexible tube
      Chain belt
    3. If the inspection result is OK on all 360° of the driver side, inspect all 360° of the passenger side of the chain belt. Refer to figures below for examples of normal and excessive wear patterns.

      Chain belt
      Pulley
      Camera flexible tube
      Guide rail

CHAIN BELT WEAR PATTERNS

Examples of OK (normal) wear patterns.

  • Chain contact surfaces appear smooth.

Examples of NG (abnormal) wear patterns.

  • Chain contact surfaces show visible scuffing.