Transmission & Driveline

P0706 Transmission Range Sensor a

14steps
~84min
3/5difficulty
Done 0 of 14
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0706

T/M RANGE SENSOR A

(Transmission Range Sensor A Circuit Range/Performance)
Diagnosis condition TCM power supply voltage: More than 11 V
Signal Transmission range switch signal
Threshold All range signals stay OFF
Diagnosis delay time Maintained for 30 seconds

POSSIBLE CAUSE

  • Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit between transmission range switch and TCM)

  • Transmission range switch

  • Control cable

Harness or connector (CAN communication line is error)

FAIL-SAFE

  • Shift position indicator on combination meter is not displayed

  • Selector shock is large

  • Start is slow

  • Acceleration is slow

  • Lock-up is not performed

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for 40 seconds or more.)

  3. Check the first trip DTC.

Is “P0706” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to Inspection and Adjustment.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Select “Self Diagnostic Results” in “TRANSMISSION”.

  3. Touch “Erase”.

  4. Perform “DTC CONFIRMATION PROCEDURE". Refer to DTC Description.

Is “P0706” detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK POWER CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect transmission range switch connector.

  3. Turn ignition switch ON.

  4. Check voltage between transmission range switch harness connector terminal and ground.

    +−Voltage
    Transmission range switch
    ConnectorTerminal
    F29 4 Ground 10 – 16 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 7.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)

  1. Turn ignition switch OFF.

  2. Disconnect TCM connector.

  3. Check continuity between transmission range switch harness connector terminals and TCM harness connector terminals.

    Transmission range switchTCMContinuity
    ConnectorTerminalConnectorTerminal
    F29 2 F25 4 Existed
    5 7
    8 6
    9 5

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2)

Check continuity between transmission range switch harness connector terminals and ground.

Transmission range switch—Continuity
ConnectorTerminal
F29 2 Ground Not existed
5
8
9

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace transmission range switch. Refer to Removal and Installation.

DETECT MALFUNCTIONING ITEMS

Check the following items:

  • Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to Wiring Diagram - IGNITION POWER SUPPLY -.

  • Harness open circuit or short circuit between IPDM E/R connector terminal 64 and transmission range switch connector terminal 4.

  • 10A fuse (No. 45, located in the IPDM E/R). Refer to IPDM E/R Terminal Arrangement.

  • IPDM E/R

Is the check result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace malfunctioning parts.

Component Inspection

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Transmission range switchConditionContinuity
Terminal
7 – 10 Manual lever: “P” and “N” positions Existed
Other than the above Not existed
4 – 5 Manual lever: “P” position Existed
Other than the above Not existed
4 – 8 Manual lever: “R” position Existed
Other than the above Not existed
4 – 9 Manual lever: “N position Existed
Other than the above Not existed
4 – 2 Manual lever: “D” position Existed
Other than the above Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

There is malfunction of transmission range switch. Replace transmission range switch. Refer to Removal and Installation.