Transmission & Driveline

P0841 Transmission Fluid Pressure Sen/sw a

9steps
~54min
4/5difficulty
Done 0 of 9
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0841

FLUID PRESS SEN/SW A

(Transmission Fluid Pressure Sensor/Switch “A” Circuit Range/Performance)
Diagnosis condition

When all of the following conditions are satisfied:

  • TCM power supply voltage: More than 11 V

  • DTC other than the applicable DTC is not detected.

  • Primary pulley speed: 300 rpm or more

  • Secondary pulley speed: 250 rpm or more

  • Target speed for shifting: Less than 0.1 seconds

  • Pulley ratio: 0.5 – 1.0

Signal —
Threshold Primary pulley pressure is outside the specified value
Diagnosis delay time Maintained for 5 seconds

POSSIBLE CAUSE

  • Harness or connector (Secondary pressure sensor circuit is open or shorted)

  • Harness or connector (Primary pressure sensor circuit is open or shorted)

  • Secondary pressure sensor

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

CHECK DTC PRIORITY

When DTC P0841 is displayed together with P17F0, diagnose first the P17F0.

Is "P17F0" detected?

YES>>

Perform diagnosis of P17F0. Refer to Diagnosis Procedure.

NO>>

GO TO 2.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>>

GO TO 3.

CHECK DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Murano vehicle.

  3. Maintain the following condition for 10 seconds or more.

    Selector lever : “D” position
    Nissan Murano Vehicle speed : Constant speed of 40 km/h
  4. Stop the Nissan Murano vehicle.

  5. Check the first trip DTC.

Is “P0841” detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CVT CHAIN

Inspect the CVT chain. Refer to Component Inspection.

Is CVT chain OK?

YES>>

GO TO 2.

NO>>

GO TO 3.

INSTALL NEW CONTROL VALVE

Install new control valve. Refer to Removal and Installation.

>>

WORK END

REPLACE SUB-ASSEMBLY AND INSTALL NEW CONTROL VALVE

Replace sub-assembly and install new control valve. Refer to Disassembly & Assembly.

>>

WORK END

Component Inspection

CVT CHAIN BELT INSPECTION

  • Place the transmission gear selector in Neutral.

  • Leave the driver door unlatched.

  1. Remove the control valve. Refer to Removal and Installation.

  2. Secure the right front tire with a suitable strap . This will assist in making the chain belt turn.

  3. Mark the left front tire with a suitable marking. This will ensure all 360° of the chain belt is inspected.

  4. Using borescope J-51951 with mirror attachment, visually inspect the entirety of the two sides of the chain belt that come in contact with the pulleys . Slowly and carefully turn the left front tire one full turn in the forward rotation to view all of the chain belt.

    Guide rail
    : Front
    1. Route the camera cable past the primary pulley and position the camera lens behind the plastic guide. See figure below.

      Chain belt Camera cable Secondary pulley
      Plastic guide Primary pulley : Front
    2. First inspect the entire 360° of the driver side of the chain belt that comes in contact with the pulley. Refer to figures below for examples of normal and excessive wear patterns.

      Pulley
      Guide rail
      Camera flexible tube
      Chain belt
    3. If the inspection result is OK on all 360° of the driver side, inspect all 360° of the passenger side of the chain belt. Refer to figures below for examples of normal and excessive wear patterns.

      Chain belt
      Pulley
      Camera flexible tube
      Guide rail

CHAIN BELT WEAR PATTERNS

Examples of OK (normal) wear patterns.

  • Chain contact surfaces appear smooth.

Examples of NG (abnormal) wear patterns.

  • Chain contact surfaces show visible scuffing.