How to Use Troubleshooting
PRECAUTION / NOTICE / HINT
HINT:
- Follow the procedure below to troubleshoot the audio and video system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
- When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
- Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
- The following 5 elements are essential for analyzing the problem:
What
Vehicle model, system name
When
Date, time, frequency of occurrence
Where
Road conditions
What were the conditions?
Driving conditions, weather conditions
How did it happen?
Problem Symptoms
|
CHECK BATTERY VOLTAGE
(a) Measure the battery voltage.
Standard voltage:
11 à 14 V
HINT:
If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.
|
CHECK INTERIOR
(a) Make sure that the conditions for condensation to form inside the cabin are limited and that the temperature there is neither too high nor too low.
OK:
The conditions for condensation to form are limited, and the temperature is neither too high nor too low.
HINT:
- A humid cabin and rapid temperature changes can easily cause condensation to form. Condensation inside the cabin may cause a short circuit.
- The audio and video system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65 °C or higher.
| NG | PROPERLY ADJUST THE CABIN TEMPERATURE |
|
CHECK CAN COMMUNICATION SYSTEM*
(a) Check the DTCs.
Click here![]()
Result:
Result | Proceed to |
|---|---|
No CAN system DTCs are output. |
A |
CAN-related DTCs are output. |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK DTCs*
(a) Refer to Check / Clear DTCs.
Click here![]()
Result:
Result | Proceed to |
|---|---|
DTCs are output. |
A |
No DTCs are output. |
B |
| B | GO TO STEP 10 |
|
CLEAR DTCs*
(a) Refer to Check / Clear DTCs.
Click here![]()
HINT:
Depending on the vehicle operating conditions, current DTCs may not indicate actual malfunctions.
|
CHECK WHETHER OTHER DTCs ARE OUTPUT*
(a) Refer to Check / Clear DTCs.
Click here![]()
Result:
Result | Proceed to |
|---|---|
DTCs are output. |
A |
No DTCs are output. |
B |
HINT:
- Even if the problem symptom is not confirmed, check the DTCs. The system stores previous DTCs in memory.
- For more information, perform another check using the "System Check Mode" screen after rechecking the DTCs with the Techstream.
- Check the DTCs and the area indicated by the code.
| B | GO TO STEP 10 |
|
DTC CHART
(a) Find the output code in the diagnostic trouble code chart.
Click here![]()
| NEXT | GO TO STEP 12 |
SYMPTOM TROUBLESHOOTING TABLE
(a) Refer to the Symptom Troubleshooting Table.
Click here![]()
Result:
Result | Proceed to |
|---|---|
The malfunction is not listed in the Symptom Troubleshooting Table. |
A |
The malfunction is listed in the Symptom Troubleshooting Table. |
B |
HINT:
If the symptom does not recur and no DTCs are output, try to reproduce the symptoms.
Click here![]()
| B | GO TO STEP 12 |
|
TROUBLESHOOT BY SYMPTOM
(a) Refer to the ECU terminals.
Click here![]()
|
CHECK THE CIRCUIT
(a) Make any necessary adjustments, repairs or replacements.
|
CHECK WHETHER OTHER DTCs ARE OUTPUT*
(a) After clearing the DTCs, check again for any DTCs.
Click here![]()
|
PERFORM CONFIRMATION TEST
| NEXT | END |