Audio / Video

Symptom Table

~26min read

SYMPTOM TROUBLESHOOTING TABLE

NOTICE:

  • When replacing the radio and display receiver assembly or the navigation ECU, always replace it with a new part. If a radio and display receiver assembly or navigation ECU previously installed on another vehicle is reused, the following may occur:
    • A communication malfunction DTC is stored.
    • The radio and display receiver assembly or navigation ECU may not operate correctly.

HINT:

  • Use the table below to determine the cause of the symptoms. If several suspected areas are listed, the possible causes of the symptom are shown in order of probability in the "Suspected Area" column of the table. Check each symptom, verifying the suspected areas in the order listed. Replace parts if necessary.
  • Check the fuses and relays associated with this system before checking the suspected areas listed below.
Display Function

Symptom

Suspected Area

Link

Black screen (no image appears on the screen)

Follow the "Black Screen" procedure

Follow the "Check Software Error History" procedure in the operation check

If the rear view of the vehicle is displayed normally on the radio and display receiver assembly when the ignition switch is in the ON (START) position and the shift lever is in the R position, replace the radio and display receiver assembly

Radio and Display Receiver Assembly

The display does not dim (does not switch to night mode) when the TAIL switch is in the ON position

Follow the "Display Illumination Does Not Dim When Illumination Control Switch Is ON" procedure

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

The power does not turn off (the screen stays on)

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

The screen is distorted

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Screen flickering or color distortion

Follow the "Screen Flickering or Color Distortion" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

The parking brake switch signal does not change in the vehicle signal check mode

Follow the "Parking Brake Switch Circuit" procedure

Radio and Display Receiver Assembly

General audio function

Symptom

Suspected Area

Link

The system does not turn on when the ignition switch is pressed

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

No sound comes from the speakers

Follow the "No Sound from Speakers" procedure

Follow the "Radio to DCM (Telematics Transceiver) Mute Signal Circuit" procedure*1

Follow the "Speaker Circuit" procedure

DCM (Data Communication Module)*1

Radio and Display Receiver Assembly

Abnormal noise is present

Follow the "Noise Interference" procedure

Radio and Display Receiver Assembly

Sound quality is poor in all modes (volume is too low)

Make sure the ASL function is turned off

-

Follow the "Poor Sound Quality in All Modes (Low Volume)" procedure

Follow the "Radio to DCM (Telematics Transceiver) Mute Signal Circuit" procedure*1

Follow the "Speaker Circuit" procedure

DCM (Data Communication Module)*1

Radio and Display Receiver Assembly

ASL does not operate

Make sure the ASL function is turned on

-

Follow the "Vehicle Speed Signal Circuit between Radio and Combination Meter" procedure*1

Radio and Display Receiver Assembly

  • *1: with Manual (SOS) Switch
Panel switch and touch screen switch function

Symptom

Suspected Area

Link

Panel switch illumination does not operate when the TAIL switch is in the ON position

Follow the "Panel Switch Illumination Does Not Operate When TAIL Switch Is ON" procedure

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

Panel switches do not operate

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Touch screen buttons do not operate

Follow the "Touch Screen Switches Do Not Operate" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Steering wheel switch function

Symptom

Suspected Area

Link

The system cannot be activated using the steering wheel switch

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Steering Wheel Switch Circuit" procedure

Radio and Display Receiver Assembly

Steering wheel switch illumination does not operate when the tail light switch is in the ON position

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

FM or AM radio operation

Symptom

Suspected Area

Link

Radio broadcasts cannot be received or reception is poor.

Follow the "Radio Broadcasts Cannot Be Received or Reception Is Poor" procedure

Radio broadcasts can be received but the station name is not displayed (some radio stations do not provide the same information)

Radio and Display Receiver Assembly

Radio broadcasts can be displayed but cannot be heard through the speakers

Operate the volume switch and increase the volume level

-

Radio and Display Receiver Assembly

Radio broadcasts can be received but the station list is not displayed

Wait 120 seconds in radio mode, then select "Refresh" on the station list screen

-

Radio and Display Receiver Assembly

Radio broadcasts can be received but the station list is not displayed

Select "Refresh" on the station list screen

-

Wait 10 minutes with the ignition switch in the ON (ACC) position, then select "Refresh" on the station list screen again

-

Radio and Display Receiver Assembly

After setting the hands-free or voice recognition function to OFF, the radio mute function does not operate

Make sure the radio mute setting is turned ON

-

Radio and Display Receiver Assembly

When the radio mute function operates, the sound is interrupted, cannot be heard, or sound quality is poor

Check whether similar symptoms occur when receiving conventional FM/AM broadcasts

-

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

When the radio mute function operates, sound can be heard but no information is displayed (some radio stations do not provide their station identification information).

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

AUX function

Symptom

Suspected Area

Link

Auxiliary device sound cannot be heard or sound quality is poor (a stereo jack of the audio system is used)

Follow the "Audio Signal Circuit between Radio and Stereo Jack Adapter" procedure

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

"AUX/VTR" does not appear on the system check mode screen

Follow the "Audio Signal Circuit between Radio and Stereo Jack Adapter" procedure

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

USB audio system function

Symptom

Suspected Area

Link

No sound from the USB audio system, or poor sound quality (USB connector in use)

Follow the procedure "Data Signal Circuit Between Audio Unit and Stereo Jack Adapter"

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

The USB device or "iPod" is not recognized

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

Track information such as track name, artist name and album name is not displayed

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

Album cover art is not displayed

Make sure the cover art display setting on the "iPod" or USB device screen is turned on

-

Check whether similar symptoms occur with another vehicle

-

If a Gracenote database update message appears on the album cover screen and update data has been downloaded to the audio and display unit, update the Gracenote database to the latest version.

-

Radio and Display Receiver Assembly

The USB device or "iPod" is recognized but cannot play, or cannot play in a specific order

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

The user-defined cover art cannot be displayed

Make sure a JPEG file is used for the album image saved in the "iPod" music data

-

Radio and Display Receiver Assembly

The "iPod" cannot be charged

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly No. 1

Radio and Display Receiver Assembly

Voice recognition function

Symptom

Suspected Area

Link

The voice menu screen is not displayed (voice recognition function is not activated)

Check whether the voice recognition guidance function is set to ON.

-

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Steering Wheel Switch Circuit" procedure

Radio and Display Receiver Assembly

When the voice recognition switch is pressed, a short beep sounds but the voice is not recognized correctly

Follow the procedure "Voice Not Recognized"

Follow the procedure "Microphone Circuit"

Radio and Display Receiver Assembly

"Bluetooth" hands-free function

Symptom

Suspected Area

Link

"Bluetooth" does not work (the in-vehicle unit cannot be found by the mobile phone)

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone cannot be registered

Follow the procedure "Mobile Phone Registration Error"

The "Bluetooth"-compatible mobile phone cannot be connected

Check whether the mobile phone is connected as a hands-free device

-

Move the mobile phone close to the in-vehicle unit and reconnect it

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone cannot connect automatically (can be connected manually)

Make sure the "Bluetooth" auto connection setting on the in-vehicle unit is set to ON

-

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone connection is disconnected

Move the mobile phone close to the in-vehicle unit and make sure it reconnects

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone cannot be connected

Check whether the mobile phone is connected as a hands-free device

-

Move the mobile phone close to the in-vehicle unit and reconnect it

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Another "Bluetooth"-compatible mobile phone is connected to the system

Check the mobile phone connection priority

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Message prompting to check whether the mobile phone is displayed

Move the mobile phone close to the in-vehicle unit and make sure it reconnects

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

When the ignition switch is turned to ON (ACC), instructions for checking the connection conditions between the mobile phone and the in-vehicle unit are displayed

Set the mobile phone connection confirmation display to OFF on the in-vehicle unit

-

Phonebook data cannot be transferred

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to ON

-

Enter "1234" on the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required)

-

Make sure no application is running on the mobile phone

-

When using the "Bluetooth" audio function, disconnect the "Bluetooth" audio player and check operation

-

Transfer the phonebook data manually

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Phonebook data is erased

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to OFF

-

Radio and Display Receiver Assembly

Phonebook data cannot be edited

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to OFF

-

Radio and Display Receiver Assembly

All transferred phonebook data is sorted under "Other"

Make sure no application is running on the mobile phone

-

Make sure the phonebook data on the mobile phone is not stored on the SIM card

-

Follow the procedure "Mobile Phone Check"

Explain to the customer that all transferred phonebook data may be stored under "Other" depending on the mobile phone

-

The mobile phone cannot make/receive calls

Move the vehicle to an area with mobile phone reception, check whether the mobile phone is connected to the vehicle via "Bluetooth" technology, and operate the in-vehicle unit again

-

Check that the mobile phone can make and receive outgoing/incoming calls correctly when it is not connected via "Bluetooth"

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The caller's voice is interrupted by noise or sound quality is poor

Check the voice reception volume (if it is too high, the voice may sound distorted)

-

Make a call with the mobile phone disconnected from "Bluetooth" and make sure the caller's voice is clearly audible

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The caller's voice cannot be heard

Check that the voice reception volume is not set to minimum

-

Make a call with the mobile phone disconnected from "Bluetooth" and make sure the caller's voice is clearly audible

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Your voice (the caller's side) is interrupted by noise or sound quality is poor

Check the voice transmission volume (if it is too high, the voice may sound distorted)

-

Make sure no object can cause noise at the microphone (air outlet from the air conditioning system pointed at the microphone, wind from an open window, additional devices, etc. can affect noise occurrence)

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Follow the procedure "Microphone Circuit"

Radio and Display Receiver Assembly

The other party cannot hear your voice

Make sure the mute button is not set to ON

-

Make sure no object can cause noise at the microphone (air outlet from the air conditioning system pointed at the microphone, wind from an open window, additional devices, etc. can affect noise occurrence)

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Follow the procedure "Microphone Circuit"

Radio and Display Receiver Assembly

No notification when a new SMS/MMS/e-mail is received*

Check the SMS/MMS/e-mail notification settings on the mobile phone and on the audio and display unit

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The received SMS/MMS/e-mail cannot be read*

Check the SMS/MMS/e-mail forwarding settings on the mobile phone and on the audio and display unit

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

It is not possible to reply to the SMS/MMS/e-mail*

Move the vehicle to an area with mobile phone reception, and check the operation of the audio and display unit and the mobile phone

-

Check whether the mobile phone can send an SMS/MMS/e-mail

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

  • *: With SMS/MMS/e-mail function
"Bluetooth" audio function

Symptom

Suspected Area

Link

The player cannot be registered

Follow the procedure "The portable player cannot be registered"

Radio and Display Receiver Assembly

The player cannot be connected manually/automatically

Follow the procedure "The portable player cannot be registered"

Follow the procedure "The portable player cannot be connected manually/automatically"

Radio and Display Receiver Assembly

A mobile phone with a portable audio player function is not recognized as a "Bluetooth" audio player even when connected via "Bluetooth"

Follow the procedure "The portable player cannot be registered"

Follow the procedure "The portable player cannot be connected manually/automatically"

Radio and Display Receiver Assembly

The portable player sound is not output from the speakers, or the sound is low

Follow the procedure "The portable player sound is not output from the speakers or the sound is low"

Radio and Display Receiver Assembly

The portable player does not play, even after selecting the "Bluetooth" audio mode

Follow the procedure "Does not play even after selecting the Bluetooth mode"

Radio and Display Receiver Assembly

The portable player does not play

Follow the procedure "Does not play even after selecting the Bluetooth mode"

Radio and Display Receiver Assembly

Track information such as track number, track name, elapsed time and playlist is not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

Portable player operation keys such as play, pause, repeat and shuffle are not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

The battery status of the portable player is not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

The "Bluetooth" signal status is not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

The pause, file selection, fast forward, fast reverse and shuffle functions of the portable player are unavailable

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

Sudden sound changes or noise during playback using the portable player

Follow the procedure "Sudden sound changes or noise during playback using the portable player"

Radio and Display Receiver Assembly

A registered component can no longer be deleted

Go to the "A registered component can no longer be deleted" item

Radio and Display Receiver Assembly

ECO information function

Symptom

Suspected Area

Link

The graph is not displayed on the "Trip Information" screen

Check again with the engine running

-

Radio and Display Receiver Assembly

The cruise control range is not displayed on the "Trip Information" screen

Turn the ignition switch to ON and check again

-

Radio and Display Receiver Assembly

The graph is not updated on the "Past record" screen even when "Clear" is selected

Turn the ignition switch to ON and check again

-

Radio and Display Receiver Assembly

The graph is not displayed on the "Past record" screen

Turn the ignition switch to ON and check again

-

Radio and Display Receiver Assembly

HD Radio function (with HD Radio function)

Symptom

Suspected Area

Link

Only "HD Radio" stations cannot be listened to or selected, or the digital or analog sound cannot be switched

Check the "HD Radio" settings

-

Radio and Display Receiver Assembly

When HD Radio is on, the album cover is not displayed

When a song not registered in Gracenote CDDB is playing, or when album cover information is not provided by the radio station, its album cover is not displayed

-

When HD Radio is on, the album cover is not displayed

Radio and Display Receiver Assembly

The radio station logo cannot be displayed

Check whether similar symptoms occur when receiving other broadcasts

-

Check whether similar symptoms occur with another vehicle

-

Radio and Display Receiver Assembly

The SPS channel cannot be selected

Make sure that the FM HD Radio mode is selected

-

After selecting "Refresh", make sure the SPS channel is in the station list

-

Radio and Display Receiver Assembly

When the SPS channel is selected, the sound cannot be heard

After selecting "Refresh", select the SPS channel from the station list

-

Radio and Display Receiver Assembly

SiriusXM Satellite Radio function (with SXM function)

Symptom

Suspected Area

Link

Satellite radio broadcasts cannot be received or reception is poor

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Pay-per-view satellite radio broadcasts cannot be received

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Satellite radio broadcasts cannot be selected, or after selecting a broadcast, it cannot be stored in memory

Go to the "Satellite radio broadcasts cannot be received" item

Go to the "Satellite radio broadcasts cannot be selected, or after selecting a broadcast, it cannot be stored in memory" item

Radio and Display Receiver Assembly

Satellite radio may be displayed but radio broadcasts cannot be heard from the speakers

Check the volume settings

-

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

The radio station logo cannot be displayed

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Satellite radio text information cannot be displayed

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

The satellite radio station cannot be selected (scanning cannot be performed)

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

When satellite radio is on, the album cover is not displayed

When a song not registered in Gracenote CDDB is playing, its album cover is not displayed

-

When satellite radio is on, the album cover is not displayed

Radio and Display Receiver Assembly

After setting the hands-free or voice recognition function to OFF, the radio mute function does not operate

Make sure the radio mute setting is turned ON

-

Radio and Display Receiver Assembly

When the radio mute function operates, the sound is interrupted, cannot be heard, or sound quality is poor

Check whether similar symptoms occur when receiving regular SiriusXM radio broadcasts

-

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

When the audio unit cache is operating, sound is heard but no information is displayed (some radio stations do not provide their station designation information)

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

"Wi-Fi" hotspot function

Symptom

Suspected Area

Link

The "Wi-Fi" connection cannot be established

Check whether the Toyota Entune App Suite function is available

Check the DCM icon on the multi-information display

-

Check the status of the "Wi-Fi" hotspot contract

-

Make sure the "Wi-Fi" hotspot function is turned on

-

Check the status of the "Wi-Fi" hotspot indicator

-

Check whether a "Wi-Fi"-compatible device in good condition can be connected to the vehicle

-

Move the vehicle to an area with few radio wave interferences and remove any accessories likely to cause radio wave interference, then check again

-

Radio and Display Receiver Assembly

Link application function

Symptom

Suspected Area

Link

The Link application function cannot be started (the smartphone battery may need charging)

Make sure the smartphone is compatible with the Link application

-

Check the smartphone settings

-

Check the connection of the smartphone to the radio receiver and display unit

-

Radio and Display Receiver Assembly

The Link application function can be started but no sound can be heard (the smartphone battery may need charging)

Make sure sound can be output from the speakers

-

Make sure sound can be output from the smartphone

-

Make sure the volume is not set to "0"

-

Make sure mute is not selected

-

Check the Link app function using another compatible smartphone

-

Radio and Display Receiver Assembly