Audio / Video

Check / Clear DTCs

~8min read

CHECK / CLEAR DTCs

CHECK DTCS (CHECK USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Navigation System / Trouble Codes.

Body Electrical > Navigation System > Trouble Codes

(e) Check the DTCs and make a note of them.

(f) Check the details of the DTC(s).

Click here

NOTICE:

The audio and visual system outputs DTCs for the following system. If DTCs other than those listed in the audio and visual system DTC chart are output, refer to the DTC chart for the applicable system.

System

Proceed to

Rear view monitor system

CLEAR DTCS (CLEAR USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Navigation System / Clear DTCs.

(e) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

ENTER DIAGNOSTIC MODE

HINT:

  • The diagrams may differ from the vehicle's screen depending on the layout of the components and the options. For this reason, some detailed areas may not be identical to those on the vehicle's screen.
  • Enter diagnostic mode at least 15 seconds after turning the ignition switch to ON. Otherwise, some items cannot be checked.

(a) There are 4 methods to enter diagnostic mode. Enter diagnostic mode using one of them.

(b) Method 1

(1) Turn the ignition switch to ON.

(2) While holding down the "AUDIO" button, operate the light control switch: OFF → Tail → OFF → Tail → OFF → Tail → OFF.

(c) Method 2

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch ON.

(3) Turn on the Techstream.

(4) Select the following menus: Body Electrical / Navigation System / Utility / Diagnostic Mode.

Body Electrical > Navigation System > Utility

Diagnostic Mode

(d) Method 3

(1) Turn the ignition switch to ON.

(2) Press the seek/track up panel switch 5 times, then press the seek/track down panel switch 5 times with the display and audio OFF.

HINT:

  • Diagnostic mode can only be started if the above operation is performed within 15 seconds of the first press of the seek/track up panel switch.
  • If the operation is not performed within 15 seconds of the first press of the seek/track panel switch, or fails, turn the display and audio system ON then OFF before attempting to start diagnostic mode.

(e) Method 4

NOTICE:

  • Do not touch the multi-display unless necessary.
  • Since the multi-display may recognize pinch-in/pinch-out or flick when operated with 2 fingers, always use one finger to operate it in diagnostic mode.

(1) Turn the ignition switch to ON.

(2) Flick the multi-display from left to right 5 times, then flick from right to left 5 times with the display and audio OFF, as shown in the illustration.

HINT:

  • Diagnostic mode can only be started if the above operation is performed within 15 seconds of the first flick from left to right.
  • If the operation is not performed within 15 seconds of the first flick from left to right, or fails, turn the display and audio system ON then OFF before attempting to start diagnostic mode.
  • The flick can be recognized anywhere on the touch area of the multi-display.

"FAILURE DIAGNOSIS" SCREEN

(a) The "Failure Diagnosis" screen is displayed by selecting "Failure Diagnosis" on the "Service Menu" screen.

SYSTEM CHECK

(a) The "System Check Mode" screen is displayed by selecting the "System Check" menu on the "Failure Diagnosis" screen.

CHECK DTCs (USING THE "SYSTEM CHECK MODE" SCREEN)

(a) Description of the System Check Mode screen

Screen Description

Display

Content

*a: Device name list No. 1

  • Device name list No. 1 shows some of the components that make up the audio and video system (for radio and display type).
  • The component names in Device name list No. 1 are shown in the following table.

*b: Check result

Displays the result codes for all components.

*c: Memory clear

  • Clears the current and past DTCs and the stored connected component names.
  • Select "Memory CLR" for 3 seconds.

*d: Recheck

  • A system check is performed again after the memory is cleared.
  • "Recheck" is greyed out during the system check.

*e: Device name list No. 2

  • Device name list No. 2 shows some of the components that make up the audio and video system (for radio and display type).
  • The component names in Device name list No. 2 are shown in the following table.
*a: Description of device name list No. 1

Name

Component

Connection method

DCU

Radio and Display Receiver Assembly

-

*b: Description of check results

Result

Meaning

Action

OK

The component does not respond by outputting a DTC.

-

DETAIL

The device responds with a DTC.

Check the DTCs on the "Unit Check Mode" screen.

NCON

The component was already present but did not respond in diagnostic mode.

  • Check the power supply circuit of the device.
  • Check the AVC-LAN communication line of the device.

NRES

The component responded in diagnostic mode but does not provide any DTC information.

  • Check the power supply circuit of the device.
  • Check the AVC-LAN communication line of the device.
*e: Description of device name list No. 2

Name

Component

Connection method

DCM

DCM (Telematics Transceiver)*

USB communication line

AUX/VTR

Stereo Jack Adapter Assembly No. 1

Vehicle wire harness

  • *: with manual (SOS) switch

(b) Description of the Unit Check Mode screen

Screen Description

Display

Content

*a: Device name

Target component

*b: History DTC

Displays the diagnostic memory results and the stored DTCs.

*c: Present DTC

Displays the DTCs output during the system check.

*d: DTC

DTC (Diagnostic Trouble Code)

*e: Timestamp

Displays the time and date of the past DTCs. (The year is displayed in 2-digit format.)

*f: Diagnosis clear

Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target component (the diagnostic system check result and the displayed data are erased).

HINT:

  • This screen is updated every second.
  • A maximum of 6 DTCs can be displayed for history and present DTCs.

(c) Record the system check result.

(1) If the check result is "DETAIL", select it on the "Unit Check Mode" screen to display the results, then record them.

NOTICE:

A maximum of 6 history and present DTCs can be displayed on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, first troubleshoot those DTCs, then check the "Unit Check Mode" screen again to see if other DTCs are displayed.

HINT:

  • When all results are "OK", no DTCs are output.
  • To view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the previous step to display the results of other devices.

(2) Check the details of the DTC(s).

Click here

NOTICE:

The audio and video system (for radio and display type) outputs DTCs for the following system. When DTCs other than those in the DTC chart for the audio and video system (for radio and display type) are output, refer to the DTC chart for the corresponding system.

System

Proceed to

Rear view monitor system

CLEAR/RECHECK DTCs (USING THE "SYSTEM CHECK MODE" SCREEN)

(a) Clear the DTCs

(1) Select "Memory CLR" for 3 seconds.

(2) Make sure the check results are cleared.

HINT:

  • To clear the DTCs for a specific device, use the "Unit Check Mode" screen.
  • When clearing DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.

(b) Recheck

(1) Select "Recheck".

(2) When the check results are displayed, make sure all DTCs are "OK". If any result other than "OK" is displayed, repeat the troubleshooting.

HINT:

After clearing the DTCs using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and repeat the procedure.

END DIAGNOSTIC MODE

(a) Turn the ignition switch OFF.