Audio / Video

USB Audio System Recognition / Playback Error

~6min read

DESCRIPTION

When a USB device or "iPod" is connected to the USB port of the stereo jack adapter assembly No. 1, it must contain playable files. The device must also communicate with and be recognized by the radio receiver and display assembly. This diagnostic procedure is performed when a device is not recognized or when the files on the device cannot be played normally.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts replaced during inspection or maintenance of the vehicle, initialization, registration or calibration may be required. Refer to the precautions for the audio and visual system.

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly that was installed in another vehicle is reused, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.

HINT:

  • If a USB device contains a large amount of data, playback may take a long time to start.
  • When using a USB device, files that are copy-protected or encrypted for copyright reasons cannot be played.
  • If files are not played in the defined order, follow the procedure below before performing the check.
    1. Add numbers in front of the file names.
    2. Place the files in a folder and copy the folder data to the USB device.

PROCEDURE

  1. CHECK THE USB DEVICE OR "iPod"

(a) Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

(b) Check whether playable files are present on the USB device or "iPod".

HINT:

Refer to the System Description section for playable files.

Click here

(c) Check whether the format of the USB device is compatible, or whether the version of the "iPod" is compatible.

HINT:

Refer to the System Description section for compatible formats and versions.

Click here

Result:

Result

Proceed to

No playable files exist, or the device format or version is not compatible.

A

Playable files exist, and the device format and version are compatible.

B

A

END (THE USB DEVICE FORMAT WAS INCOMPATIBLE, THE "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)

B
  1. CHECK THE WIRE HARNESS AND CONNECTOR (RADIO RECEIVER AND DISPLAY ASSEMBLY - STEREO JACK ADAPTER ASSEMBLY No. 1)

(a) Disconnect the radio receiver and display assembly connector.

(b) Disconnect the connector from the stereo jack adapter assembly No. 1.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

j1-1 (UP1) - j4-1 (USV1)

Always

Below 1 Ω

j1-2 (UDO-) - j4-2 (US1-)

Always

Below 1 Ω

j1-3 (UDO+) - j4-3 (US1+)

Always

Below 1 Ω

j1-4 (UJSG) - j4-4 (UGD1)

Always

Below 1 Ω

j1-5 (UJSS) - j4-5 (USG1)

Always

Below 1 Ω

j1-1 (UP1) - Body ground

Always

10 kΩ minimum

j1-2 (UDO-) - Body ground

Always

10 kΩ minimum

j1-3 (UDO+) - Body ground

Always

10 kΩ minimum

j1-4 (UJSG) - Body ground

Always

10 kΩ minimum

j1-5 (UJSS) - Body ground

Always

10 kΩ minimum

*a

Front view of wire harness side connector

(to radio receiver and display assembly)

*b

Front view of wire harness side connector

(to stereo jack adapter assembly No. 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK THE RADIO RECEIVER AND DISPLAY ASSEMBLY (POWER SUPPLY TO THE STEREO JACK ADAPTER ASSEMBLY No. 1)

(a) Reconnect the j4 connector of the radio receiver and display assembly.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

j1-1 (UP1) - j1-4 (UJSG)

Ignition Switch in ACC position

5 V

*a

Front view of wire harness side connector

(to stereo jack adapter assembly No. 1)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

OK
  1. FORMAT THE USB DEVICE OR RESTORE THE "iPod" AND CHECK AGAIN

(a) Delete all files from the USB device or "iPod" and format/restore it.

(b) Save the data again and check whether it can be played on the device in the vehicle.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure a backup of the music data is available before performing this operation.

OK:

The malfunction disappears.

OK

END (USB OR "iPod" DEFECTIVE)

NG
  1. REPLACE USB DEVICE OR "iPod"

(a) Turn the ignition switch OFF.

HINT:

When this malfunction occurs, the ignition switch must be turned to OFF so the vehicle can recognize a new device when it is connected.

(b) Turn the ignition switch to ACC.

(c) Connect a good USB device or "iPod" to the stereo jack adapter assembly No. 1.

HINT:

  • If the malfunction occurred while a USB device was being used, use a different USB device to perform the check. If the malfunction occurred while an "iPod" was being used, use a different "iPod" to perform the check.
  • Refer to the System Description section for compatible formats and versions.

    Click here

NEXT
  1. CHECK THE USB DEVICE OR "iPod"

(a) Check whether the USB device or "iPod" is recognized by the radio receiver and display assembly, and whether information such as track, artist and album names is shown on the display.

OK:

The USB device or "iPod" is correctly recognized and the information is shown on the display.

OK

THE USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE