Audio / Video

Telematics Transceiver Disconnected (B15DB)

~6min read

DESCRIPTION

If the radio and display receiver assembly cannot detect the DCM (telematics transceiver) for a certain period (90 seconds) after the ignition switch is turned ON (ACC), and the radio and display receiver assembly confirms that the information is missing by checking the previous DCM (telematics transceiver) recognition information (stored information), this DTC will be stored.

The telematics system uses USB communication between devices. If there is an open, short to +B or short to ground in the USB circuit, communication is interrupted and the telematics system will not operate normally.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B15DB

Telematics Transceiver Disconnected

DCM Disconnected (Telematics Transceiver)

  • Wire harness or connector
  • DCM (Telematics Transceiver)
  • DCM (Telematics Transceiver) Power Source Circuit
  • Radio and Display Receiver Assembly

HINT:

This DTC may be stored due to environmental factors such as noise or interference, for example.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts replaced during inspection or maintenance of the vehicle, initialization, registration or calibration may be required. Refer to the precautions for the audio and visual system.

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly that was installed in another vehicle is reused, the following may occur:
    • A communication malfunction DTC is stored.
    • The radio and display receiver assembly may not operate normally.
  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the DCM (telematics transceiver), refer to the registration section.

    Click here

PROCEDURE

  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the ignition switch OFF.

(c) Turn the ignition switch to ON and wait 90 seconds.

(d) Check the DTCs again and make sure no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) POWER SOURCE)

(a) Disconnect the DCM (telematics transceiver) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-4 (E) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F134-1 (+B) - F134-4 (E)

Ignition Switch in OFF position

11 à 14 V

F134-8 (ACC) - F134-4 (E)

Ignition Switch in ACC position

11 à 14 V

F134-7 (IG2) - F134-4 (E)

Ignition Switch in ON position

11 à 14 V

*a

Front view of wire harness side connector

(to DCM (telematics transceiver))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER AND DISPLAY ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Disconnect the F130 radio receiver and display assembly connector.

(b) Disconnect the F133 DCM (telematics transceiver) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F130-10 (USBV) - F133-5 (USBV)

Always

Below 1 Ω

F130-11 (USBG) - F133-3 (USBG)

Always

Below 1 Ω

F130-10 (USBV) or F133-5 (USBV) - Body ground

Always

10 kΩ minimum

F130-11 (USBG) or F133-3 (USBG) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the radio receiver and display assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F130-11 (USBG) - Body ground

Always

Below 1 Ω

*a

Component without wire harness connected

(Radio and Display Receiver Assembly)

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F130-10 (USBV) - F130-11 (USBG)

ignition switch in ACC position

4,75 à 5,25 V

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - RADIO RECEIVER AND DISPLAY ASSEMBLY)

(a) Disconnect the F133 DCM (telematics transceiver) connector.

(b) Disconnect the F136 radio receiver and display assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F133-2 (USB+) - F136-1 (USB+)

Always

Below 1 Ω

F133-1 (USB-) - F136-2 (USB-)

Always

Below 1 Ω

F133-6 (USBS) - F136-3 (USBS)

Always

Below 1 Ω

F133-2 (USB+) or F136-1 (USB+) - Body ground

Always

10 kΩ minimum

F133-1 (USB-) or F136-2 (USB-) - Body ground

Always

10 kΩ minimum

F133-6 (USBS) or F136-3 (USBS) - Body ground

Always

10 kΩ minimum

*a

Front view of wire harness side connector

(to DCM (telematics transceiver))

*b

Front view of wire harness side connector

(to radio receiver and display assembly)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK DCM (TELEMATICS TRANSCEIVER)

(a) Replace the DCM (telematics transceiver) with a new one.

Click here

(b) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Turn the ignition switch to ON and wait 90 seconds.

(e) Check the DTCs again and make sure no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

END (DCM [TELEMATICS TRANSCEIVER] IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY