Amplifier Antenna
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
w/ Seat Heater System |
- |
- |
*1 |
SPARE WHEEL COVER ASSEMBLY |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*C |
w/ Seat Heater System |
- |
- |
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*3 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*4 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
*5 |
REAR SEAT CUSHION ASSEMBLY |
*6 |
REAR SEAT CUSHION LOCK HOOK |
*7 |
REAR SIDE SEATBACK ASSEMBLY LH |
*8 |
REAR SIDE SEATBACK ASSEMBLY RH |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
ANTENNA CORD SUB-ASSEMBLY |
*2 |
NO. 1 AMPLIFIER ANTENNA ASSEMBLY |
*3 |
NO. 2 AMPLIFIER ANTENNA ASSEMBLY |
*4 |
ROOF SIDE INNER GARNISH LH |
*5 |
ROOF SIDE INNER GARNISH RH |
*6 |
ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*7 |
ROOF SIDE RAIL GARNISH ASSEMBLY RH |
*8 |
CLIP |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
PROCEDURE
1. INSTALL ANTENNA CORD SUB-ASSEMBLY
(a) Connect the connector to install the antenna cord sub-assembly.
HINT:
Use the same procedure for the RH side and LH side.
2. INSTALL NO. 2 AMPLIFIER ANTENNA ASSEMBLY
(a) Engage the 2 guides and install the No. 2 amplifier antenna assembly with the bolt.
Torque:
6 N·m {61 kgf·cm, 53 in·lbf}
(b) Connect the 2 connectors.
3. INSTALL NO. 1 AMPLIFIER ANTENNA ASSEMBLY
HINT:
Use the same procedure as for the No. 2 amplifier antenna assembly.
4. INSTALL ROOF SIDE INNER GARNISH LH
Click here ![]()
5. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
6. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
7. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
10. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
11. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
12. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
13. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
14. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
15. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
16. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
18. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
19. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
20. INSPECT SRS WARNING LIGHT
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during amplifier antenna assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
10. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here ![]()
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE NO. 2 AMPLIFIER ANTENNA ASSEMBLY
(a) Disconnect the 2 connectors. |
![]() |
(b) Remove the bolt.
(c) Disengage the 2 guides to remove the No. 2 amplifier antenna assembly.
18. REMOVE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
HINT:
Use the same procedure as for the No. 2 amplifier antenna assembly.
19. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) Disconnect the connector to remove the antenna cord sub-assembly. HINT: Use the same procedure for the RH side and LH side. |
![]() |




