Stereo Component Amplifier Disconnected (B15D3). Telematics Transceiver Disconnected (B15DB). Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)
Stereo Component Amplifier Disconnected (B15D3)
DESCRIPTION
The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B15D3 |
Stereo Component Amplifier Disconnected |
When either of the following conditions is met:
|
|
HINT:
The radio and display receiver assembly is the master unit.
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
CHECK DTC
(a) If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.
Result | Proceed to |
|---|---|
DTC B15C3 is not output. |
A |
DTC B15C3 is output. |
B |
| B | GO TO DTC B15C3 |
|
CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
(a) Check that optional components (including associated wiring) which generate radio waves are not installed.
Result | Proceed to |
|---|---|
Optional components (including associated wiring) are installed. |
A |
Optional components (including associated wiring) are not installed. |
B |
HINT:
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
- This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
| B | GO TO STEP 4 |
|
REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
(a) Remove optional components (including associated wiring).
NOTICE:
Do not remove optional components or associated wiring without the permission of the customer.
|
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
|
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
(a) Disconnect the G10 and G8 stereo component amplifier assembly connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G10-3 (GND) - Body ground |
Always |
Below 1 Ω |
G10-18 (GND2) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G10-1 (+B) - G10-3 (GND) |
Always |
11 to 14 V |
G10-16 (+B2) - G10-3 (GND) |
Always |
11 to 14 V |
G8-12 (ACC) - G10-3 (GND) |
Engine switch on (ACC) |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
(a) Disconnect the G3 radio and display receiver assembly connector.
(b) Disconnect the G8 stereo component amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G3-5 (TX1+) - G8-8 (TX+) |
Always |
Below 1 Ω |
G3-6 (TX1-) - G8-7 (TX-) |
Always |
Below 1 Ω |
G3-5 (TX1+) or G8-8 (TX+) - Body ground |
Always |
10 kΩ or higher |
G3-6 (TX1-) or G8-7 (TX-) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
(a) Replace the stereo component amplifier assembly with a new or known good one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Telematics Transceiver Disconnected (B15DB)
DESCRIPTION
If the radio and display receiver assembly cannot detect the DCM (telematics transceiver) for a certain period of time (90 seconds) after the engine switch is turned on (ACC) and the radio and display receiver assembly confirms that the information is missing by checking past DCM (telematics transceiver) recognition information (registered information), this DTC will be stored.
The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B15DB |
Telematics Transceiver Disconnected |
DCM (telematics transceiver) disconnected |
|
HINT:
This DTC may be stored due to environmental reasons such as electrical noise or interference.
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the DCM (telematics transceiver), refer to Registration.
Click here

PROCEDURE
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Turn the engine switch off.
(c) Turn the engine switch on (IG) and wait for 90 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | USE SIMULATION METHOD TO CHECK |
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) POWER SOURCE)
(a) Disconnect the G9 DCM (telematics transceiver) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G9-4 (E) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G9-1 (+B) - G9-4 (E) |
Always |
11 to 14 V |
G9-8 (ACC) - G9-4 (E) |
Engine switch on (ACC) |
11 to 14 V |
G9-7 (IG2) - G9-4 (E) |
Engine switch on (IG) |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
(a) Disconnect the G1 radio and display receiver assembly connector.
(b) Disconnect the G11 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G1-10 (USBV) - G11-5 (USBV) |
Always |
Below 1 Ω |
G1-11 (USBG) - G11-3 (USBG) |
Always |
Below 1 Ω |
G1-10 (USBV) or G11-5 (USBV) - Body ground |
Always |
10 kΩ or higher |
G1-11 (USBG) or G11-3 (USBG) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
(a) Disconnect the G1 radio and display receiver assembly connector.
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G1-10 (USBV) - G1-11 (USBG) |
Engine switch on (ACC) |
4.75 to 5.25 V |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - NAVIGATION ECU)
(a) Disconnect the G11 DCM (telematics transceiver) connector.
(b) Disconnect the G113 navigation ECU connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK DCM (TELEMATICS TRANSCEIVER)
(a) Replace the DCM (telematics transceiver) with a new one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Turn the engine switch off.
(d) Turn the engine switch on (IG) and wait for 90 seconds.
(e) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END (DCM (TELEMATICS TRANSCEIVER) IS DEFECTIVE) |
|
CHECK NAVIGATION ECU
(a) Replace the navigation ECU with a new one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Turn the engine switch off.
(d) Turn the engine switch on (IG) and wait for 90 seconds.
(e) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END (NAVIGATION ECU IS DEFECTIVE) |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)
DESCRIPTION
This DTC is stored when items controlled by the air conditioning amplifier assembly cannot be customized via the navigation system vehicle customization screen.
HINT:
The air conditioning amplifier assembly controls the air conditioning system related items that are customizable via the navigation system vehicle customization screen.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B15F5 |
Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction |
Air conditioning amplifier assembly vehicle setting processing malfunction |
|
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here ![]()
OK:
CAN communication DTCs are not output.
| NG | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK AIR CONDITIONING SYSTEM
(a) Check if the air conditioning system is malfunctioning.
Click here ![]()
HINT:
Customization may not be possible depending on the malfunction in the air conditioning system.
OK:
No malfunctions are present in the air conditioning system.
| NG | GO TO AIR CONDITIONING SYSTEM |
|
CHECK CUSTOMIZE ITEMS
(a) Make a note of the customizable items for the air conditioning system.
HINT:
The items shown as customizable via the navigation system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.
(1) To match-up the items on the navigation system vehicle customization screen with the items on the Techstream, check the customize parameters list for the air conditioning system related items that can be customized via the navigation system vehicle customization screen.
Click here ![]()
(b) Using the Techstream, check that it is possible to change the settings of the customize parameters that are available for customization via the navigation system vehicle customization screen.
OK:
The items available for customization via the navigation system vehicle customization screen can be customized successfully using the Techstream.
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |

