XM Tuner Antenna Disconnected (B15FE,B15FF). GVIF Disconnected (from Extension Module to H/U) (B153A). AV Signal Stoppage (Low Battery Voltage) (B158F)
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the telephone antenna assembly which is connected to the radio and display receiver assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B15FE |
XM Tuner Antenna Disconnected |
The telephone antenna assembly is not connected |
|
B15FF |
XM Tuner Antenna Short |
A short occurs in the telephone antenna assembly |
|
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY
(a) Replace the No. 4 antenna cord sub-assembly with a new or known good one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
|
REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY
(a) Replace the No. 3 antenna cord sub-assembly with a new or known good one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
|
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
(a) Replace the No. 2 antenna cord sub-assembly with a new or known good one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
|
REPLACE TELEPHONE ANTENNA ASSEMBLY
(a) Replace the telephone antenna assembly with a new or known good one.
Click here ![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
GVIF Disconnected (from Extension Module to H/U) (B153A)
DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B153A |
GVIF Disconnected (from Extension Module to H/U) |
GVIF disconnected (from navigation ECU to radio and display receiver assembly) |
|
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
PROCEDURE
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | USE SIMULATION METHOD TO CHECK |
|
CHECK HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
(a) Disconnect the G109 navigation ECU connector. |
|
(b) Disconnect the G110 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G109-1 (GVO-) - G110-1 (GV2-) |
Always |
Below 1 Ω |
G109-2 (GVO+) - G110-2 (GV2+) |
Always |
Below 1 Ω |
G109-3 (GVG1) - G110-3 (GVG2) |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
REPLACE NAVIGATION ECU
(a) Replace the navigation ECU with a new one.
Click here ![]()
|
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END (NAVIGATION ECU IS DEFECTIVE) |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION
This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B158F |
AV Signal Stoppage (Low Battery Voltage) |
A video or audio signal is interrupted when the battery voltage drops |
|
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK VEHICLE SIGNAL (OPERATION CHECK)
(a) Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check. Click here |
![]() |
(b) Measure the battery voltage.
Standard Voltage:
11 to 14 V
HINT:
This display is updated once per second.
| NG | GO TO STEP 3 |
|
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
(a) Disconnect the G3 radio and display receiver assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G3-4 (+B1) - Body ground |
Always |
11 to 14 V |
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |

