Navigation Ecu
Components
COMPONENTS
ILLUSTRATION
*1 |
CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
*2 |
CONSOLE BOX POCKET SUB-ASSEMBLY |
*3 |
FRONT CONSOLE UPPER PANEL GARNISH |
*4 |
LOWER INSTRUMENT PANEL FINISH PANEL LH |
*5 |
LOWER INSTRUMENT PANEL FINISH PANEL RH |
- |
- |
ILLUSTRATION
*A |
w/o Manual (SOS) Switch |
*B |
w/ Manual (SOS) Switch |
*1 |
CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
*2 |
CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL |
*3 |
NAVIGATION ECU WITH BRACKET |
*4 |
NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
*5 |
RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET |
- |
- |
ILLUSTRATION
*A |
w/o Manual (SOS) Switch |
*B |
w/ Manual (SOS) Switch |
*1 |
DCM (TELEMATICS TRANSCEIVER) WITH ANTENNA CORD |
*2 |
NAVIGATION ECU |
*3 |
NO. 1 TELEPHONE BRACKET |
*4 |
NO. 2 TELEPHONE BRACKET |
*5 |
NO. 5 ANTENNA CORD SUB-ASSEMBLY |
*6 |
WIRING HARNESS CLAMP |
Installation
INSTALLATION
PROCEDURE
1. PRECAUTION
NOTICE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the navigation ECU, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the radio and display receiver assembly.
2. INSTALL NAVIGATION ECU
3. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH ANTENNA CORD (w/ Manual (SOS) Switch)
4. INSTALL NO. 1 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Engage the guide and install the No. 1 telephone bracket with the 2 screws.
(b) w/ Manual (SOS) Switch:
(1) Engage the 3 guides and install the No. 1 telephone bracket with the 3 screws.
5. INSTALL NO. 2 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Engage the guide and install the No. 2 telephone bracket with the 2 screws.
(2) Engage the wiring harness clamp.
(b) w/ Manual (SOS) Switch:
(1) Engage the 3 guides and install the No. 2 telephone bracket with the 3 screws.
(2) Engage the wiring harness clamp.
(3) Engage the clamp.
6. INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY
Click here ![]()
7. INSTALL NAVIGATION ECU WITH BRACKET
(a) w/o Manual (SOS) Switch:
(1) Connect each connector.
(2) Install the navigation ECU with bracket with the 2 nuts as shown in the illustration.
![]() |
Install in this Direction |
(3) Connect the connector.
(b) w/ Manual (SOS) Switch:
(1) Connect each connector.
(2) Install the navigation ECU with bracket with the 2 nuts as shown in the illustration.
![]() |
Install in this Direction |
(3) Connect the 2 connectors.
8. INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
9. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here ![]()
10. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
11. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
13. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
14. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the navigation ECU, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the radio and display receiver assembly.
2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
4. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
5. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
7. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
8. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
9. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here ![]()
10. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
11. REMOVE NAVIGATION ECU WITH BRACKET
(a) w/o Manual (SOS) Switch:
(1) Disconnect the connector. |
![]() |
(2) Remove the 2 nuts and pull the navigation ECU with bracket as shown in the illustration.
![]() |
Remove in this Direction |
(3) Disconnect each connector and remove the navigation ECU with bracket.
(b) w/ Manual (SOS) Switch:
(1) Disconnect the 2 connectors. |
![]() |
(2) Remove the 2 nuts and pull the navigation ECU with bracket as shown in the illustration.
![]() |
Remove in this Direction |
(3) Disconnect each connector and remove the navigation ECU with bracket.
12. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY
Click here ![]()
13. REMOVE NO. 2 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Disengage the wiring harness clamp. |
![]() |
(2) Remove the 2 screws and disengage the guide to remove the No. 2 telephone bracket. |
![]() |
(b) w/ Manual (SOS) Switch:
(1) Disengage the clamp. |
![]() |
(2) Disengage the wiring harness clamp. |
![]() |
(3) Remove the 3 screws and disengage the 3 guides to remove the No. 2 telephone bracket. |
![]() |
14. REMOVE NO. 1 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Remove the 2 screws and disengage the guide to remove the No. 1 telephone bracket. |
![]() |
(b) w/ Manual (SOS) Switch:
(1) Remove the 3 screws and disengage the 3 guides to remove the No. 1 telephone bracket. |
![]() |
15. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH ANTENNA CORD (w/ Manual (SOS) Switch)
16. REMOVE NAVIGATION ECU










