Radio Receiver
Components
COMPONENTS
ILLUSTRATION
*1 |
CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
*2 |
CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
*3 |
CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL |
*4 |
CONSOLE BOX POCKET SUB-ASSEMBLY |
*5 |
FRONT CONSOLE UPPER PANEL GARNISH |
*6 |
LOWER INSTRUMENT PANEL FINISH PANEL LH |
*7 |
LOWER INSTRUMENT PANEL FINISH PANEL RH |
*8 |
RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET |
ILLUSTRATION
*1 |
INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY |
*2 |
NO. 1 RADIO RECEIVER BRACKET |
*3 |
NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
*4 |
NO. 2 RADIO RECEIVER BRACKET |
*5 |
RADIO AND DISPLAY RECEIVER ASSEMBLY |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. PRECAUTION
(a) w/o Navigation System:
NOTICE:
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
(b) w/ Navigation System:
NOTICE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the radio and display receiver assembly, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the navigation ECU.
2. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY
3. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Engage the 8 claws to install the No. 2 instrument panel register assembly as shown in the illustration.
![]() |
Install in this Direction |
4. INSTALL NO. 2 RADIO RECEIVER BRACKET
(a) Install the No. 2 radio receiver bracket with the 4 screws.
5. INSTALL NO. 1 RADIO RECEIVER BRACKET
(a) Install the No. 1 radio receiver bracket with the 4 screws.
6. INSTALL INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY
Click here ![]()
7. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
(a) Connect each connector.
(b) Engage the 5 clips to temporarily install the radio and display receiver assembly with bracket as shown in the illustration.
![]() |
Install in this Direction |
(c) Install the radio and display receiver assembly with bracket with the 4 bolts.
8. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
9. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
11. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
12. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
(a) w/o Navigation System:
NOTICE:
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
(b) w/ Navigation System:
NOTICE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the radio and display receiver assembly, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the navigation ECU.
2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
4. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
5. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
7. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
8. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
9. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
(a) Remove the 4 bolts. |
![]() |
(b) Pull the radio and display receiver assembly with bracket toward the rear of the vehicle to disengage the 5 clips.
![]() |
Remove in this Direction |
(c) Disconnect each connector and remove the radio and display receiver assembly with bracket.
10. REMOVE INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY
Click here ![]()
11. REMOVE NO. 1 RADIO RECEIVER BRACKET
(a) Remove the 4 screws and No. 1 radio receiver bracket. |
![]() |
12. REMOVE NO. 2 RADIO RECEIVER BRACKET
(a) Remove the 4 screws and No. 2 radio receiver bracket. |
![]() |
13. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Disengage the 8 claws and remove the No. 2 instrument panel register assembly as shown in the illustration.
![]() |
Remove in this Direction |
14. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY




