Navigation Antenna
Components
COMPONENTS
ILLUSTRATION
*A |
w/o Manual (SOS) Switch |
*B |
w/ Manual (SOS) Switch |
*1 |
NAVIGATION ANTENNA ASSEMBLY |
*2 |
NAVIGATION ANTENNA ASSEMBLY WITH BRACKET |
*3 |
NAVIGATION ANTENNA BRACKET |
- |
- |
Inspection
INSPECTION
PROCEDURE
1. INSPECT NAVIGATION ANTENNA ASSEMBLY
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the navigation antenna assembly. |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL NAVIGATION ANTENNA BRACKET
2. INSTALL NAVIGATION ANTENNA ASSEMBLY
(a) Engage the 6 guides and 2 claws to install the navigation antenna assembly as shown in the illustration.
*A |
w/o Manual (SOS) Switch |
*B |
w/ Manual (SOS) Switch |
![]() |
Install in this Direction |
- |
- |
3. INSTALL NAVIGATION ANTENNA ASSEMBLY WITH BRACKET
(a) Install the navigation antenna assembly with bracket with the 2 screws.
(b) Engage the 2 claws.
(c) Connect the connector.
4. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during navigation antenna assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
2. REMOVE NAVIGATION ANTENNA ASSEMBLY WITH BRACKET
(a) Disconnect the connector. |
![]() |
(b) Disengage the 2 claws.
(c) Remove the 2 screws and navigation antenna assembly with bracket. |
![]() |
3. REMOVE NAVIGATION ANTENNA ASSEMBLY
(a) Disengage the 2 claws and 6 guides to remove the navigation antenna assembly as shown in the illustration.
*A |
w/o Manual (SOS) Switch |
*B |
w/ Manual (SOS) Switch |
![]() |
Remove in this Direction |
- |
- |
4. REMOVE NAVIGATION ANTENNA BRACKET





