Illumination Circuit. Illumination for Panel Switch does not Come on with Tail Switch ON. Microphone Circuit
Illumination Circuit
DESCRIPTION
Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.
WIRING DIAGRAM
NOTICE:
- The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK ILLUMINATION
(a) Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
Result | Proceed to |
|---|---|
Illumination comes on for all components except steering pad switch assembly. |
A |
Illumination comes on for all components except radio and display receiver assembly. |
B |
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). |
C |
| B | GO TO STEP 5 |
| C | GO TO LIGHTING SYSTEM |
|
CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
(a) Disconnect the G17 spiral cable sub-assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G17-14 (IL+2) - Body ground |
Light control switch in tail or head position |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT STEERING PAD SWITCH ASSEMBLY
(a) Remove the steering pad switch assembly.
Click here ![]()
(b) Inspect the steering pad switch assembly.
Click here ![]()
| NG | REPLACE STEERING PAD SWITCH ASSEMBLY |
|
INSPECT SPIRAL CABLE SUB-ASSEMBLY
(a) Remove the spiral cable sub-assembly.
Click here ![]()
(b) Inspect the spiral cable sub-assembly.
Click here ![]()
| OK | REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, COMBINATION METER ASSEMBLY) |
| NG | REPLACE SPIRAL CABLE SUB-ASSEMBLY |
CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-15 (ILL+) - Body ground |
Light control switch in tail or head position |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Disconnect the G16 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-16 (ILL-) - G16-1 (ILL-) |
Always |
Below 1 Ω |
G2-16 (ILL-) or G16-1 (ILL-) - Body ground |
Always |
10 kΩ or higher |
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Illumination for Panel Switch does not Come on with Tail Switch ON
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
CHECK VEHICLE SIGNAL (OPERATION CHECK)
(a) Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check. Click here |
![]() |
(b) Check that the display changes between ON and OFF according to the light control switch operation.
OK:
Light Control Switch | Display |
|---|---|
Tail or head |
ON |
Off or AUTO |
OFF |
HINT:
- This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.
- Make sure to move the vehicle to a bright area before performing an operation check with the light control switch in the AUTO position.
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
Microphone Circuit
DESCRIPTION
- w/o Manual (SOS) Switch:
The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.
- w/ Manual (SOS) Switch:
The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the DCM (telematics transceiver) sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the DCM (telematics transceiver).
WIRING DIAGRAM
w/o Manual (SOS) Switch
w/ Manual (SOS) Switch
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
- Before replacing the DCM (telematics transceiver), refer to Registration.
Click here

PROCEDURE
CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
(a) Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check. Click here |
![]() |
(b) When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
OK:
Check result is normal.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
(a) Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check. Click here |
![]() |
(b) When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
OK:
Check result is normal.
Result | Proceed to |
|---|---|
NG (w/o Manual (SOS) Switch) |
A |
NG (w/ Manual (SOS) Switch) |
B |
OK |
C |
| B | GO TO STEP 9 |
| C | GO TO STEP 19 |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Disconnect the O10 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-25 (SNS2) - O10-6 (SNS2) |
Always |
Below 1 Ω |
G2-23 (MACC) - O10-9 (MACC) |
Always |
Below 1 Ω |
G2-21 (MIN+) - O10-8 (MCO+) |
Always |
Below 1 Ω |
G2-22 (MIN-) - O10-7 (MCO-) |
Always |
Below 1 Ω |
G2-25 (SNS2) or O10-6 (SNS2) - Body ground |
Always |
10 kΩ or higher |
G2-23 (MACC) or O10-9 (MACC) - Body ground |
Always |
10 kΩ or higher |
G2-21 (MIN+) or O10-8 (MCO+) - Body ground |
Always |
10 kΩ or higher |
G2-22 (MIN-) or O10-7 (MCO-) - Body ground |
Always |
10 kΩ or higher |
G2-24 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
(a) Connect the G2 radio and display receiver assembly connector.
(b) Connect the O10 roof console box sub-assembly connector.
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-24 (SGND) - Body ground |
Always |
Below 1 Ω |
G2-22 (MIN-) - Body ground |
Always |
Below 1 Ω |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Connect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | GO TO STEP 8 |
|
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
(a) Connect the G2 radio and display receiver assembly connector.
(b) Connect the O10 roof console box sub-assembly connector.
(c) Turn the engine switch on (ACC).
(d) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the O10 roof console box sub-assembly connector. |
|
(e) Check the signal waveform according to the condition(s) in the table below.
Item | Condition |
|---|---|
Measurement terminal |
O10-8 (MCO+) - O10-7 (MCO-) |
Tool setting |
50 mV/DIV., 500 ms/DIV. |
Vehicle condition |
|
OK:
The waveform is similar to that shown in the illustration.
HINT:
The oscilloscope waveform shown in the illustration is an example for reference only.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Disconnect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK | REPLACE TELEPHONE MICROPHONE ASSEMBLY |
| NG | REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY |
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Disconnect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK | REPLACE TELEPHONE MICROPHONE ASSEMBLY |
| NG | REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Disconnect the O10 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-25 (SNS2) - O10-6 (SNS2) |
Always |
Below 1 Ω |
G2-25 (SNS2) or O10-6 (SNS2) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Disconnect the G9 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-21 (MIN+) - G9-18 (MCO+) |
Always |
Below 1 Ω |
G2-22 (MIN-) - G9-19 (MCO-) |
Always |
Below 1 Ω |
G2-21 (MIN+) or G9-18 (MCO+) - Body ground |
Always |
10 kΩ or higher |
G2-22 (MIN-) or G9-19 (MCO-) - Body ground |
Always |
10 kΩ or higher |
G2-24 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY)
(a) Disconnect the G9 DCM (telematics transceiver) connector.
(b) Disconnect the O10 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G9-33 (MCVD) - O10-9 (MACC) |
Always |
Below 1 Ω |
G9-34 (MCI+) - O10-8 (MCO+) |
Always |
Below 1 Ω |
G9-35 (MCI-) - O10-7 (MCO-) |
Always |
Below 1 Ω |
G9-33 (MCVD) or O10-9 (MACC) - Body ground |
Always |
10 kΩ or higher |
G9-34 (MCI+) or O10-8 (MCO+) - Body ground |
Always |
10 kΩ or higher |
G9-35 (MCI-) or O10-7 (MCO-) - Body ground |
Always |
10 kΩ or higher |
G9-32 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
(a) Disconnect the G9 DCM (telematics transceiver) connector.
(b) Connect the G2 radio and display receiver assembly connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-24 (SGND) - Body ground |
Always |
Below 1 Ω |
G2-22 (MIN-) - Body ground |
Always |
Below 1 Ω |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
INSPECT DCM (TELEMATICS TRANSCEIVER)
(a) Connect the G9 DCM (telematics transceiver) connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G9-35 (MCI-) - Body ground |
Always |
Below 1 Ω |
G9-32 (SGND) - Body ground |
Always |
Below 1 Ω |
| NG | REPLACE DCM (TELEMATICS TRANSCEIVER) |
|
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Connect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | GO TO STEP 18 |
|
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO DCM (TELEMATICS TRANSCEIVER))
(a) Connect the G2 radio and display receiver assembly connector.
(b) Connect the O10 roof console box sub-assembly connector.
(c) Connect the G9 DCM (telematics transceiver) connector.
(d) Turn the engine switch on (ACC).
(e) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the O10 roof console box sub-assembly connector. |
|
(f) Check the signal waveform according to the condition(s) in the table below.
Item | Condition |
|---|---|
Measurement terminal |
O10-8 (MCO+) - O10-7 (MCO-) |
Tool setting |
50 mV/DIV., 500 ms/DIV. |
Vehicle condition |
|
OK:
The waveform is similar to that shown in the illustration.
HINT:
The oscilloscope waveform shown in the illustration is an example for reference only.
| NG | GO TO STEP 17 |
|
INSPECT DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
(a) Connect the G2 radio and display receiver assembly connector.
(b) Connect the O10 roof console box sub-assembly connector.
(c) Connect the G9 DCM (telematics transceiver) connector.
(d) Turn the engine switch on (ACC).
(e) Connect an oscilloscope to terminals 18 (MCO+) and 19 (MCO-) of the G9 DCM (telematics transceiver) connector. |
|
(f) Check the signal waveform according to the condition(s) in the table below.
Item | Condition |
|---|---|
Measurement terminal |
G9-18 (MCO+) - G9-19 (MCO-) |
Tool setting |
50 mV/DIV., 500 ms/DIV. |
Vehicle condition |
|
OK:
The waveform is similar to that shown in the illustration.
HINT:
The oscilloscope waveform shown in the illustration is an example for reference only.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG | REPLACE DCM (TELEMATICS TRANSCEIVER) |
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Disconnect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK | REPLACE TELEPHONE MICROPHONE ASSEMBLY |
| NG | REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY |
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
(a) Remove the roof console box sub-assembly.
Click here ![]()
(b) Disconnect the B telephone microphone assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK | REPLACE TELEPHONE MICROPHONE ASSEMBLY |
| NG | REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
(a) Disconnect the G1 radio and display receiver assembly connector.
(b) Disconnect the G13 navigation ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G1-25 (MCO+) - G13-13 (MIC+) |
Always |
Below 1 Ω |
G1-26 (MCO-) - G13-14 (MIC-) |
Always |
Below 1 Ω |
G1-25 (MCO+) or G13-13 (MIC+) - Body ground |
Always |
10 kΩ or higher |
G1-26 (MCO-) or G13-14 (MIC-) - Body ground |
Always |
10 kΩ or higher |
G1-24 (SGND) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)
(a) Disconnect the G13 navigation ECU connector.
(b) Turn the engine switch on (ACC).
(c) Check the signal waveform according to the condition(s) in the table below.
OK: The waveform is similar to that shown in the illustration. HINT: The oscilloscope waveform shown in the illustration is an example for reference only. |
|
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |













