Rear Crossing Traffic Alert Buzzer
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
w/ Seat Heater System |
- |
- |
*1 |
SPARE WHEEL COVER ASSEMBLY |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*C |
w/ Seat Heater System |
- |
- |
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*3 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*4 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
*5 |
REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH |
*6 |
REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH |
*7 |
REAR SEAT CUSHION ASSEMBLY |
*8 |
REAR SEAT CUSHION LOCK HOOK |
*9 |
REAR SIDE SEATBACK ASSEMBLY LH |
*10 |
REAR SIDE SEATBACK ASSEMBLY RH |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
BLIND SPOT MONITOR BUZZER |
*2 |
PACKAGE TRAY TRIM PANEL ASSEMBLY |
*3 |
REAR SEAT SHOULDER BELT COVER |
*4 |
ROOF SIDE INNER GARNISH LH |
*5 |
ROOF SIDE INNER GARNISH RH |
*6 |
ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*7 |
ROOF SIDE RAIL GARNISH ASSEMBLY RH |
*8 |
CLIP |
● |
Non-reusable part |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL BLIND SPOT MONITOR BUZZER
(a) Connect the connector.
(b) Engage the clamp to install the blind spot monitor buzzer.
2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here ![]()
3. INSTALL REAR SEAT SHOULDER BELT COVER
Click here ![]()
4. INSTALL CENTER STOP LIGHT SET
Click here ![]()
5. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here ![]()
6. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7. INSTALL ROOF SIDE INNER GARNISH LH
Click here ![]()
8. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
9. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
10. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
13. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
14. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
16. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
17. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
18. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
19. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
21. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
22. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
23. INSPECT SRS WARNING LIGHT
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blind spot monitor buzzer removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
10. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here ![]()
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here ![]()
18. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE CENTER STOP LIGHT SET
Click here ![]()
20. REMOVE REAR SEAT SHOULDER BELT COVER
Click here ![]()
21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here ![]()
22. REMOVE BLIND SPOT MONITOR BUZZER
(a) Disengage the clamp. |
![]() |
(b) Disconnect the connector to remove the blind spot monitor buzzer.


