Does not Play even after Bluetooth Audio Mode is Selected. Dtc Check / Clear. Freeze Frame Data
Does not Play even after Bluetooth Audio Mode is Selected
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
HINT:
Even if the portable player can play audio content, it may not be able to play via the in-vehicle device. This does not necessarily indicate a malfunction of the in-vehicle device.
PROCEDURE
CHECK OPERATION
(a) Check if the portable player operates normally.
OK:
The portable player operates normally.
| NG | MALFUNCTION IN PORTABLE PLAYER |
|
CHECK AUDIO SETTINGS
(a) Set volume, fader and balance to the initial values and check that the sound is normal.
OK:
Audio system returns to normal.
HINT:
Sound quality adjustment measures vary according to the type of amplifier.
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
CHECK USING ANOTHER "Bluetooth" AUDIO COMPATIBLE VEHICLE OF SAME MODEL
(a) Check if the "Bluetooth" audio player plays normally on another "Bluetooth" audio compatible vehicle of the same model.
OK:
"Bluetooth" audio player plays normally.
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG | MALFUNCTION IN PORTABLE PLAYER |
Dtc Check / Clear
DTC CHECK / CLEAR
CHECK DTC (CHECK USING TECHSTREAM)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG) and wait for 90 seconds.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Body Electrical > Navigation System > Trouble Codes(e) Check for DTCs, and then write them down.
(f) Check the details of the DTC(s).
Click here ![]()
NOTICE:
The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
System | Proceed to |
|---|---|
Parking Assist Monitor System |
CLEAR DTC (CLEAR USING TECHSTREAM)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG) and wait for 90 seconds.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Body Electrical > Navigation System > Clear DTCs(e) Clear the DTCs.
START DIAGNOSTIC MODE
HINT:
- Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
- If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace the malfunctioning parts. (for 14 Speakers)
Click here

- Start diagnostic mode at least 90 seconds after turning the engine switch on (IG). Otherwise, some items cannot be checked.
(a) There are 4 methods to start diagnostic mode. Start diagnostic mode by using one of them.
(b) Method 1
(1) Turn the engine switch on (IG).
(2) While pressing and holding the "AUDIO" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.
(3) Diagnostic mode will start and the "Service Menu" screen will be displayed.
(c) Method 2
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Body Electrical / Navigation System / Utility / Diagnostic Mode.
Body Electrical > Navigation System > UtilityDiagnostic Mode
(5) Diagnostic mode will start and the "Service Menu" screen will be displayed.
(d) Method 3
(1) Turn the engine switch on (IG).
(2) Press the seek/track up panel switch 5 times and then press the seek/track down panel switch 5 times with the screen and audio turned off.
HINT:
- Diagnostic mode can only be started if the above operation is completed within 15 seconds of the first press of the seek/track up panel switch.
- If the operation is not completed within 15 seconds of the first press of the seek/track panel switch or fails, turn the screen and audio on and then off again before attempting to start diagnostic mode.
(3) Diagnostic mode will start and the "Service Menu" screen will be displayed.
(e) Method 4
NOTICE:
- Do not touch the multi-display except when necessary.
- Since the multi-display may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate it in diagnostic mode.
(1) Turn the engine switch on (IG).
(2) Perform a flick operation on the multi-display screen from the left to the right 5 times and then perform a flick operation from the right to left 5 times with the screen and audio turned off as shown in the illustration.
HINT:
- Diagnostic mode can only be started if the above operation is completed within 15 seconds of the first flick from the left to the right.
- If the operation is not completed within 15 seconds of the first flick from the left to the right or fails, turn the screen and audio on and then off before attempting to start diagnostic mode again.
- Flick operations can be recognized anywhere within the touch area of the multi-display screen.
(3) Diagnostic mode will start and the "Service Menu" screen will be displayed.
FAILURE DIAGNOSIS
(a) The "Failure Diagnosis" screen will be displayed by selecting "Failure Diagnosis" on the "Service Menu" screen.
SYSTEM CHECK
(a) The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.
CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)
HINT:
When "NCON" is displayed for all devices connected via AVC-LAN communication, or when all device names are not displayed, check if there is a short in an AVC-LAN line or device connected to the AVC-LAN. Repair or replace parts as necessary. (for 14 Speakers)
Click here ![]()
(a) System check mode screen description
Screen Description Display | Content |
|---|---|
*a: Device name list No. 1 |
|
*b: Check result |
Result codes for all devices are displayed. |
*c: Memory clear |
|
*d: Recheck |
|
*e: Device name list No. 2 |
|
Name | Component | Connection Method |
|---|---|---|
| *: for 14 Speakers | ||
DCU |
Radio and display receiver assembly |
- |
DSP-AMP |
Stereo component amplifier assembly* |
AVC-LAN communication line |
CAA |
Television camera assembly |
Vehicle wire harness |
Result | Meaning | Action |
|---|---|---|
| *: for 14 Speakers | ||
OK |
The device does not respond with a DTC. |
- |
DETAIL |
The device responds with a DTC. |
Read the DTCs on the "Unit Check Mode" screen. |
NCON |
The device was previously present, but did not respond in diagnostic mode. |
|
NRES |
The device responded in diagnostic mode, but gives no DTC information.* |
|
Name | Component | Connection Method |
|---|---|---|
DCM |
DCM (telematics transceiver)* |
USB Communication line |
AUX/VTR |
Stereo jack adapter assembly |
Vehicle wire harness |
- *: w/ Manual (SOS) Switch
(b) Unit check mode screen description
Screen DescriptionDisplay | Content |
|---|---|
*a: Device name |
Target device |
*b: History DTC |
Diagnostic memory results and stored DTCs are displayed. |
*c: Present DTC |
DTCs output in the service check are displayed. |
*d: DTC |
DTC (Diagnostic Trouble Code) |
*e: Timestamp* |
The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.) |
*f: Diagnosis clear |
Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared). |
- *: w/ GPS Time Setting Function
HINT:
- This screen is updated once per second.
- A maximum of 6 DTCs can be displayed for history and present DTCs.
(c) Read the system check result.
(1) If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.
NOTICE:
A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.
HINT:
- When all results are "OK", no DTCs are present.
- When proceeding to view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.
(2) Check the details of the DTC(s).
Click here ![]()
NOTICE:
The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
System | Proceed to |
|---|---|
Parking Assist Monitor System |
DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)
(a) Clear the DTCs
(1) Select "Memory CLR" for 3 seconds.
(2) Check that the check results are cleared.
HINT:
- To clear the DTCs for a specific device, use the "Unit Check Mode" screen.
- When clearing the DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.
(b) Recheck
(1) Select "Recheck".
(2) Check that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.
HINT:
When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.
FINISH DIAGNOSTIC MODE
(a) Turn the engine switch off.
Freeze Frame Data
FREEZE FRAME DATA
CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Body Electrical > Navigation System > Trouble Codes(e) Select a DTC to display its freeze frame data.
LIST OF FREEZE FRAME DATA
Body Electrical > Navigation SystemTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Battery Voltage |
Battery voltage |
Min.: 0 V, Max.: 24 V |
11 to 14 V |
- |
Active Dimmer |
Active dimmer function |
ON or OFF |
ON: Active dimmer function on OFF: Active dimmer function off |
- |
Tail Light SW |
Taillight switch |
ON or OFF |
ON: Light control switch in tail or head position OFF: Light control switch off or AUTO |
- |
Reverse Signal |
Reverse signal |
ON or OFF |
ON: Shift lever in R OFF: Shift lever not in R |
- |
Parking Brake |
Parking brake switch |
ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
Ignition |
Engine switch |
ON or OFF |
ON: Engine switch on (IG) OFF: Engine switch off or on (ACC) |
"OFF" is displayed even though the engine switch is on (ACC) |
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h, Max.: 255 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
HDMI Line(Blu-ray Disc Player) |
- |
Disconnected or Connected |
Disconnected |
Not available |