Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier. Mute Signal Circuit between Radio Receiver and Telematics Transceiver. Mute Signal Circuit between Stereo Component Amplifier
Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier
DESCRIPTION
This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.
If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.
If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
(a) Disconnect the G3 radio and display receiver assembly connector.
(b) Disconnect the G8 stereo component amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G3-25 (MUT1) - G8-1 (MUTE) |
Always |
Below 1 Ω |
G3-25 (MUT1) or G8-1 (MUTE) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
(a) Reconnect the G8 stereo component amplifier assembly connector.
(b) Disconnect the G3 radio and display receiver assembly connector.
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |
Mute Signal Circuit between Radio Receiver and Telematics Transceiver
DESCRIPTION
The DCM (telematics transceiver) sends a mute signal to the radio and display receiver assembly.
The radio and display receiver assembly controls the volume according to the mute signal from the DCM (telematics transceiver).
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
- Before replacing the DCM (telematics transceiver), refer to Registration.
Click here

PROCEDURE
INSPECT DCM (TELEMATICS TRANSCEIVER)
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
(a) Disconnect the G2 radio and display receiver assembly connector.
(b) Disconnect the G9 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G2-3 (TMUT) - G9-17 (MUTE) |
Always |
Below 1 Ω |
G2-3 (TMUT) or G9-17 (MUTE) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
(a) Disconnect the G9 DCM (telematics transceiver) connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE DCM (TELEMATICS TRANSCEIVER) |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver
DESCRIPTION
The DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly.
The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver).
WIRING DIAGRAM
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- Before replacing the DCM (telematics transceiver), refer to Registration.
Click here

PROCEDURE
INSPECT DCM (TELEMATICS TRANSCEIVER)
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
(a) Disconnect the G8 stereo component amplifier assembly connector.
(b) Disconnect the G9 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G8-24 (TMUT) - G9-17 (MUTE) |
Always |
Below 1 Ω |
G8-24 (TMUT) or G9-17 (MUTE) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
(a) Disconnect the G9 DCM (telematics transceiver) connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE DCM (TELEMATICS TRANSCEIVER) |
| NG | REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |





