USB Device Malfunction (B1585). Black Screen. Camera ECU Malfunction (C1610)
USB Device Malfunction (B1585)
DESCRIPTION
This DTC is stored when a malfunction occurs in a connected device.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B1585 |
USB Device Malfunction |
When any of the following conditions is met:
|
|
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
REPLACE USB DEVICE OR "iPod"
(a) Disconnect the USB device or "iPod" from the stereo jack adapter assembly.
(b) Turn the power switch off.
HINT:
When this DTC has been stored, it is necessary to turn the power switch off to make it possible for the vehicle to recognize a new device when it is connected.
(c) Turn the power switch on (ACC).
(d) Connect a known good USB device or "iPod" to the stereo jack adapter assembly.
HINT:
- If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
- Refer to System Description for compatible formats and versions.
Click here

|
CHECK DTC
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR USB DEVICE OR "iPod" WAS DEFECTIVE) |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Black Screen
PROCEDURE
CHECK DISPLAY SETTING
(a) Check that the display is not in screen off mode.
OK:
The display setting is not in screen off mode.
| NG | CHANGE SCREEN TO SCREEN ON MODE |
|
CHECK IMAGE QUALITY SETTING
(a) Check that the screen color quality can be set.
OK:
Setting is possible.
| OK | SET SCREEN COLOR QUALITY TO NORMAL |
| NG | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
Camera ECU Malfunction (C1610)
DESCRIPTION
This DTC is stored when a malfunction occurs in the parking assist monitor system.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1610 |
Camera ECU Malfunction |
Malfunction occurs in the parking assist monitor system |
|
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here

- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
CHECK DTC (PARKING ASSIST MONITOR SYSTEM)
(a) Clear the DTCs.
Chassis > Parking Assist Camera > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Parking Assist Camera > Trouble CodesOK:
No DTCs are output.
| NG | GO TO PARKING ASSIST MONITOR SYSTEM |
|
CHECK DTC (AUDIO AND VISUAL SYSTEM)
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |