Noise Filter
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
w/ Seat Heater System |
- |
- |
*1 |
SPARE WHEEL COVER ASSEMBLY |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*C |
w/ Seat Heater System |
*D |
for High Mounted Stop Light |
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
RADIO SETTING CONDENSER |
*3 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*4 |
REAR SEAT CUSHION ASSEMBLY |
*5 |
REAR SEAT CUSHION LOCK HOOK |
*6 |
REAR SIDE SEATBACK ASSEMBLY LH |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |
ILLUSTRATION
*A |
for Window Defogger |
- |
- |
*1 |
RADIO SETTING CONDENSER |
*2 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*3 |
ROOF SIDE INNER GARNISH LH |
*4 |
ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*5 |
CLIP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
PROCEDURE
1. INSTALL RADIO SETTING CONDENSER (for Window Defogger)
(a) Engage the claw to install a new terminal cover to the wire harness. NOTICE:
|
![]() |
(b) Engage the 3 claws to install the new terminal cover with wire harness to a new condenser as shown in the illustration.
![]() |
Install in this Direction |
NOTICE:
- Do not use excessive force when inserting the terminal cover into the condenser.
- If the terminal cover has been deformed during installation, replace the terminal, terminal cover and condenser with new ones.
(c) Engage the clamp to temporarily install a new radio setting condenser with wire harness.
(d) Install the new radio setting condenser with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
2. INSTALL ROOF SIDE INNER GARNISH LH
Click here ![]()
3. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
5. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)
(a) Engage the claw to install a new terminal cover to the wire harness. NOTICE:
HINT: Use the same procedure for the other terminal cover. |
![]() |
(b) Engage the 6 claws to install 2 new terminal covers with wire harness to a new condenser as shown in the illustration.
![]() |
Install in this Direction |
NOTICE:
- Do not use excessive force when inserting the terminal covers into the condenser.
- If a terminal cover has been deformed during installation, replace the terminal, terminal covers and condenser with new ones.
(c) Insert the cover as shown in the illustration and engage the claw.
![]() |
Install in this Direction |
(d) Engage the clamp to temporarily install the new radio setting condenser with wire harness.
(e) Install the new radio setting condenser with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
6. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
7. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
8. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
9. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
10. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
13. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
14. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
15. INSPECT SRS WARNING LIGHT
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT RADIO SETTING CONDENSER (for High Mounted Stop Light)
(a) With the radio setting condenser installed, check that there is no looseness or other abnormalities.
(b) Measure the resistance of the radio setting condenser according to the value(s) in the table below. Standard Resistance:
|
|
|||||||||||||
(c) Remove the bolt.
(d) Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
(e) Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below. Standard Resistance:
Standard Voltage:
|
|
|||||||||||||||||||||||||||||||||
2. INSPECT RADIO SETTING CONDENSER (for Window Defogger)
(a) With the radio setting condenser installed, check that there is no looseness or other abnormalities.
(b) Measure the resistance of the radio setting condenser according to the value(s) in the table below. Standard Resistance:
|
|
|||||||||||||
(c) Remove the bolt.
(d) Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
(e) Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below. Standard Resistance:
Standard Voltage:
|
|
|||||||||||||||||||||||||
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radio setting condenser removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
10. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)
NOTICE:
When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.
(a) Remove the bolt. |
![]() |
(b) Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
(c) Disengage the claw and pull out the cover as shown in the illustration.
![]() |
Remove in this Direction |
(d) Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser as shown in the illustration.
![]() |
Remove in this Direction |
(e) Using a screwdriver, bend back and break off the claw as shown in the illustration. HINT: Use the same procedure for the other terminal cover. |
![]() |
(f) Remove the 2 terminal covers from the wire harness.
NOTICE:
- Make sure to hold the crimped side of the terminal when disconnecting the wire harness from the terminal cover.
- Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
- Check for deformation of the terminal after the wire harness has been removed from the terminal cover.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
13. REMOVE ROOF SIDE INNER GARNISH LH
Click here ![]()
14. REMOVE RADIO SETTING CONDENSER (for Window Defogger)
NOTICE:
When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.
(a) Remove the bolt. |
![]() |
(b) Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
(c) Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser as shown in the illustration.
![]() |
Remove in this Direction |
(d) Using a screwdriver, bend back and break off the claw as shown in the illustration. |
![]() |
(e) Remove the terminal cover from the wire harness.
NOTICE:
- Make sure to hold the crimped side of the terminal when disconnecting the wire harness from the terminal cover.
- Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
- Check for deformation of the terminal after the wire harness has been removed from the terminal cover.














