Parking Assist Ecu
Components
COMPONENTS
ILLUSTRATION
*1 |
PARKING ASSIST ECU |
*2 |
PARKING ASSIST ECU COVER |
Installation
INSTALLATION
PROCEDURE
1. INSTALL PARKING ASSIST ECU
(a) Turn back the front floor carpet assembly and front floor mat as shown in the illustration. |
![]() |
(b) Engage the 2 guides to temporarily install the parking assist ECU as shown in the illustration.
![]() |
Install in this Direction (1) |
![]() |
Install in this Direction (2) |
(c) Install the parking assist ECU with the bolt.
(d) Install the front floor carpet assembly and front floor mat to its original position as shown in the illustration. |
![]() |
(e) Engage the clamp.
(f) Connect each connector.
2. INSTALL PARKING ASSIST ECU COVER
(a) Install the parking assist ECU cover with the 3 clips.
3. INSTALL FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
4. PERFORM CALIBRATION
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during parking assist ECU removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of parking assist ECU |
|
Panoramic View Monitor System |
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of parking assist ECU |
|
Panoramic View Monitor System |
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
2. REMOVE PARKING ASSIST ECU COVER
(a) Remove the 3 clips and parking assist ECU cover. |
![]() |
3. REMOVE PARKING ASSIST ECU
(a) Disconnect each connector. |
![]() |
(b) Disengage the clamp.
(c) Turn back the front floor carpet assembly and front floor mat as shown in the illustration. |
![]() |
(d) Remove the bolt. |
![]() |
(e) Disengage the 2 guides and remove the parking assist ECU as shown in the illustration.
![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |










