XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the roof antenna assembly, which is connected to the radio and display receiver assembly.
DTC No. | Detection Item | DTC Detection Condition | Suspected Area |
|---|---|---|---|
B15FE |
XM Tuner Antenna Disconnected |
Roof antenna assembly is not connected |
|
B15FF |
XM Tuner Antenna Short Circuit |
Short circuit in roof antenna assembly |
|
WIRING DIAGRAM
PRECAUTION / NOTICE / HINT
NOTICE:
- Depending on the parts replaced during vehicle inspection or maintenance, initialization, registration or calibration may be required. Refer to the precautions for the navigation system.
Click here
.gif)
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly that was installed in another vehicle is reused, the following may occur:
- A communication malfunction DTC is stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
REPLACE ANTENNA CABLE SUB-ASSEMBLY
(a) Replace the antenna cable sub-assembly with a new or normally functioning one.
Click here![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Check DTCs again and confirm that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTC is output.
Result:
Result | Proceed to |
|---|---|
OK |
A |
NG (for TMMT manufactured) |
B |
NG (for TMC manufactured) |
C |
| A | END (ANTENNA CABLE SUB-ASSEMBLY WAS FAULTY) |
| C | GO TO STEP 5 |
|
CHECK ANTENNA CABLE SUB-ASSEMBLY NO. 2
(a) Disconnect the antenna cable sub-assembly No. 2 connector from the antenna cable sub-assembly. |
|
(b) Disconnect the antenna cable sub-assembly No. 2 connector from the antenna cable sub-assembly No. 3.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
AB-2 - BC-2 |
Always |
Below 1 Ω |
AB-2a - BC-2a |
Always |
Below 1 Ω |
AB-2 - Body Ground |
Always |
10 kΩ minimum |
AB-2a - Body Ground |
Always |
10 kΩ minimum |
| NG | REPLACE NO. 2 ANTENNA CABLE SUB-ASSEMBLY |
|
INSPECT ANTENNA CABLE ASSY NO. 3
(a) Disconnect the No. 3 antenna cable assy connector from the No. 2 antenna cable assy. |
|
(b) Disconnect the No. 3 antenna cable assy connector from the roof antenna assy.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
BC-2 - CD-3 |
Always |
Below 1 Ω |
BC-2a - CD-3a |
Always |
Below 1 Ω |
BC-2 - Body Ground |
Always |
10 kΩ minimum |
BC-2a - Body Ground |
Always |
10 kΩ minimum |
| NG | REPLACE NO. 3 ANTENNA CABLE SUB-ASSEMBLY |
|
REPLACE ROOF ANTENNA ASSY
(a) Replace the roof antenna assy with a new or normally functioning part.
Click here![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Check DTCs again and confirm that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTC is output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
CHECK ANTENNA CABLE SUB-ASSEMBLY NO. 2
(a) Disconnect the antenna cable sub-assembly No. 2 connector from the antenna cable sub-assembly. |
|
(b) Disconnect the antenna cable sub-assembly No. 2 connector from the antenna cable sub-assembly No. 3.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
AB-2 - BC-2 |
Always |
Below 1 Ω |
AB-2a - BC-2a |
Always |
Below 1 Ω |
AB-2 - Body Ground |
Always |
10 kΩ minimum |
AB-2a - Body Ground |
Always |
10 kΩ minimum |
| NG | REPLACE NO. 2 ANTENNA CABLE SUB-ASSEMBLY |
|
INSPECT ANTENNA CABLE ASSY NO. 3
(a) Disconnect the No. 3 antenna cable assy connector from the No. 2 antenna cable assy. |
|
(b) Disconnect the No. 3 antenna cable assy connector from the roof antenna assy.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
BC-2 - CD |
Always |
Below 1 Ω |
BC-2a - CD-3a |
Always |
Below 1 Ω |
BC-2 - Body Ground |
Always |
10 kΩ minimum |
BC-2a - Body Ground |
Always |
10 kΩ minimum |
| NG | REPLACE NO. 3 ANTENNA CABLE SUB-ASSEMBLY |
|
REPLACE ROOF ANTENNA ASSY
(a) Replace the roof antenna assy with a new or normally functioning part.
Click here![]()
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Check DTCs again and confirm that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTC is output.
| OK | END |
| NG | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
.png)
.png)
.png)
.png)