Navigation / Multi-Display

Microphone Circuit

4steps
~24min
2/5difficulty
Done 0 of 4

DESCRIPTION

The Radio Receiver and Display Assembly, Reading Light Assembly and Telephone Microphone Assembly are connected to each other using microphone connection detection signal lines.

Through this circuit, the DCM (Telematics Transceiver) supplies power to the Reading Light Assembly and Telephone Microphone Assembly, and the Reading Light Assembly and Telephone Microphone Assembly send microphone signals to the Radio Receiver and Display Assembly via the DCM (Telematics Transceiver).

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts replaced during vehicle inspection or maintenance, initialization, registration or calibration may be required. Refer to the precautions for the navigation system.

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly that was installed in another vehicle is reused, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.

PROCEDURE

  1. CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)

(a) Select the "Microphone Check" screen. Refer to the Check Microphone (Input to Navigation ECU) section in Operation Check.

Click here

(b) When voice is picked up by the microphone, check whether the microphone input level value changes according to the voice.

OK:

The check result is normal.

OK

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

NG
  1. CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER AND DISPLAY ASSEMBLY)

(a) Select the "Microphone Check" screen. Refer to Microphone Check (Input to Radio Receiver and Display Assembly) in Operation Check.

Click here

(b) When voice is picked up by the microphone, check whether the microphone input level value changes according to the voice.

OK:

The check result is normal.

NG

GO TO STEP 11

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

(a) Disconnect the F131 connector from the radio and display receiver assembly.

(b) Disconnect connector R2 from the map light assembly (telephone microphone assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F131-25 (SNS2) - R2-1 (SNS2)

Always

Below 1 Ω

F131-25 (SNS2) or R2-1 (SNS2) - Body Ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER AND DISPLAY ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Disconnect the F131 connector from the radio and display receiver assembly.

(b) Disconnect the F134 DCM (telematics transceiver) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F131-21 (MIN+) - F134-18 (MCO+)

Always

Below 1 Ω

F131-22 (MIN-) - F134-19 (MCO-)

Always

Below 1 Ω

F131-21 (MIN+) or F134-18 (MCO+) - Body Ground

Always

10 kΩ minimum

F131-22 (MIN-) or F134-19 (MCO-) - Body Ground

Always

10 kΩ minimum

F131-24 (SGND) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (DCM (DATA COMMUNICATION MODULE) - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

(a) Disconnect connector F134 from the DCM (Data Communication Module).

(b) Disconnect connector R2 from the map light assembly (telephone microphone assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-33 (MCVD) - R2-9 (MACC)

Always

Below 1 Ω

F134-34 (MIC+) - R2-8 (MCO+)

Always

Below 1 Ω

F134-35 (MIC-) - R2-7 (MCO-)

Always

Below 1 Ω

F134-33 (MCVD) or R2-9 (MACC) - Body Ground

Always

10 kΩ minimum

F134-34 (MIC+) or R2-8 (MCO+) - Body Ground

Always

10 kΩ minimum

F134-35 (MIC-) or R2-7 (MCO-) - Body Ground

Always

10 kΩ minimum

F134-32 (SGND) - Body Ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect connector F134 from the DCM (Data Communication Module).

(b) Connect the radio and display receiver assembly connector.

*a

Component with Wire Harness Connected

(Radio and Display Receiver Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F131-24 (SGND) - Body ground

Always

Below 1 Ω

F131-22 (MIN-) - Body ground

Always

Below 1 Ω

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

OK
  1. CHECK DCM (TELEMATICS TRANSCEIVER)

(a) Connect the DCM (Telematics Transceiver) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F134-33 (MCVD) - Body Ground

Engine switch in ON (ACC) position

4 à 6 V

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-35 (MIC-) - Body ground

Always

Below 1 Ω

F134-32 (SGND) - Body Ground

Always

Below 1 Ω

NG

REPLACE DCM (DATA COMMUNICATION MODULE)

OK
  1. CHECK MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

(a) Remove the map light assembly (telephone microphone assembly).

Click here

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

1 (SNS2) - 7 (MCO-)

Always

Below 1 Ω

*a

Component without wire harness connected

(Map light assembly (telephone microphone assembly))

NG

REPLACE MAP LIGHT ASSEMBLY (OUTPUT TO DCM (TELEMATICS TRANSCEIVER))

OK
  1. CHECK READING LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (OUTPUT TO DCM (TELEMATICS TRANSCEIVER))

(a) Connect the F131 connector of the Audio and Display System Assembly.

(b) Connect the map light assembly connector (telephone microphone assembly).

(c) Connect the F134 connector of the DCM (Telematics Transceiver).

(d) Turn the ignition switch to ACC.

(e) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the map light assembly R2 connector.

*a

Component with Wire Harness Connected

(Map light assembly (telephone microphone assembly))

(f) Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:

Result

Proceed to

A waveform synchronized with the voice volume sent to the Reading Light Assembly (Telephone Microphone Assembly) is output.

A

No waveform synchronized with the voice volume sent to the Reading Light Assembly (Telephone Microphone Assembly) is output.

B

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

A
  1. CHECK DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO RECEIVER AND DISPLAY ASSEMBLY)

(a) Connect the F131 connector of the Audio and Display System Assembly.

(b) Connect the map light assembly R2 connector.

(c) Connect the DCM (telematics transceiver) connector.

(d) Turn the ignition switch to ACC.

(e) Connect an oscilloscope to terminals 18 (MCO+) and 19 (MCO-) of the F134 connector of the DCM (Telematics Transceiver).

*a

Component with Wire Harness Connected

DCM (Telematics Transceiver)

(f) Check the signal waveform under the condition(s) listed in the table below.

Item

Condition

Test probe

F134-18 (MCO+) - F134-19 (MCO-)

Oscilloscope Setting

50 mV/DIV., 500 ms/DIV.

Vehicle Operating Conditions

  1. Turn the ignition switch to ACC.
  2. Sound is sent to the map light assembly when the user is within 125 mm of the sound holes of the map light assembly.

OK:

The waveform is the same as that shown in the diagram.

HINT:

The oscilloscope waveform shown in the diagram is an example for reference only.

OK

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

NG

REPLACE DCM (DATA COMMUNICATION MODULE)

  1. CHECK WIRE HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

(a) Disconnect the F130 radio receiver and display assembly connector.

(b) Disconnect connector F135 from the navigation ECU.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F130-25 (MCO+) - F135-13 (MIC+)

Always

Below 1 Ω

F130-26 (MCO-) - F135-14 (MIC-)

Always

Below 1 Ω

F130-25 (MCO+) or F135-13 (MIC+) - Body ground

Always

10 kΩ minimum

F130-26 (MCO-) or F135-14 (MIC-) - Body ground

Always

10 kΩ minimum

F130-24 (SGND) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)

(a) Disconnect the navigation ECU connector F135.

(b) Turn the engine switch to ON (ACC).

(c) Check the signal waveform under the condition(s) listed in the table below.

Item

Condition

Test probe

F135-13 (MIC+) - F135-14 (MIC-)

Oscilloscope Setting

50 mV/DIV., 500 ms/DIV.

Vehicle Operating Conditions

  1. Turn the ignition switch to ACC.
  2. Sound is sent to the map light assembly when the user is within 125 mm of the sound holes of the map light assembly.

OK:

The waveform is the same as that shown in the diagram.

HINT:

The oscilloscope waveform shown in the diagram is an example for reference only.

*a

Front view of wire harness side connector

(to navigation ECU)

OK

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY