Navigation / Multi-Display

Vehicle Speed Signal Malfunction (B15C2)

~5min read

DESCRIPTION

The navigation ECU receives a vehicle speed signal sent from the combination meter, as well as information from the navigation antenna assembly, and then adjusts the vehicle position on the map.

The navigation ECU stores this DTC when the difference between the speed information received by the navigation antenna assembly and the SPD pulse received by the combination meter assembly becomes too large.

HINT:

  • A voltage of 12 V or 5 V is output from each ECU to the instrument cluster assembly. The signal is converted into a pulse signal by the transistor located in the instrument cluster assembly. Each ECU controls its respective system based on this pulse signal.
  • If there is a short circuit in any ECU or in the wire harness connected to an ECU, none of the systems shown in the following diagram will operate normally.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B15C2

Vehicle speed signal malfunction

Difference detected between GPS speed and SPD pulse

  • Meter / Gauge System
  • Navigation ECU
  • Radio and Display Receiver Assembly
  • Wire harness or connector

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts replaced during vehicle inspection or maintenance, initialization, registration or calibration may be required. Refer to the precautions for the navigation system.

    Click here

  • When replacing the radio and display receiver assembly or the navigation ECU, always replace it with a new part. If a radio and display receiver assembly or navigation ECU previously installed on another vehicle is reused, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly or navigation ECU may not operate correctly.

PROCEDURE

  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Check DTCs again and confirm that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK VEHICLE SENSOR (OPERATION CHECK)

(a) Go to the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

Click here

(b) While driving, compare the "Speed" value with the speedometer value. Make sure these values are almost identical.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following check procedure referring to the values shown on the Data List of the skid control ECU, as it is the source of the vehicle speed signal.

OK:

The vehicle speed displayed on the "System Sensor Check" screen is almost identical to the actual vehicle speed measured using the Techstream.

Click here

OK

GO TO STEP 5

NG
  1. CHECK INSTRUMENT CLUSTER ASSEMBLY (OUTPUT WAVEFORM)

(a) Check the output waveform.

(1) Remove the combination meter assembly with the connector(s) still connected.

(2) Connect an oscilloscope to terminal F4-6 (+S) and body ground.

(3) Turn the engine switch on (IG).

(4) Slowly turn one wheel.

(5) Check the signal waveform according to the condition(s) listed in the table below.

Item

Condition

Test probe

F4-6 (+S) - Body ground

Oscilloscope Setting

5 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

One wheel is turned

OK:

The waveform is the same as that shown in the diagram.

HINT:

When the system is operating normally, one wheel revolution generates 4 pulses. As vehicle speed increases, the width indicated by (A) in the diagram decreases.

*a

Component with Wire Harness Connected

(instrument cluster assembly)

NG

GO TO METER/GAUGE SYSTEM

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

(a) Disconnect the navigation ECU connector F135.

(b) Disconnect the combination meter assembly connector F4.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F135-9 (SPD) - F4-6 (+S)

Always

Below 1 Ω

F135-9 (SPD) or F4-6 (+S) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE NAVIGATION ECU

(a) Replace the navigation ECU with a new one.

Click here

NEXT
  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Check DTCs again and confirm that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

END (NAVIGATION ECU IS FAULTY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY