Navigation / Multi-Display

Symptom Table

~47min read

SYMPTOM TROUBLESHOOTING TABLE

NOTICE:

  • Depending on the parts replaced during vehicle inspection or maintenance, initialization, registration or calibration may be required. Refer to the precautions for the navigation system.

    Click here

  • When replacing the radio and display receiver assembly or the navigation ECU, always replace it with a new part. If a radio and display receiver assembly or navigation ECU previously installed on another vehicle is reused, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly or navigation ECU may not operate correctly.

HINT:

  • Use the table below to determine the cause of the symptoms. If several suspected areas are listed, the possible causes of the symptom are shown in order of probability in the "Suspected Area" column of the table. Check each symptom, verifying the suspected areas in the order listed. Replace parts if necessary.
  • Check the fuses and relays associated with this system before checking the suspected areas listed below.
General Function

Symptom

Suspected Area

Link

The navigation function and voice recognition function cannot be used, and the above symptoms occur after restarting repeatedly, with the engine switch in ON (ACC) position

Make sure that "MEU" is displayed on the "System Check Mode" screen and that the "OK" message is displayed

Make sure the navigation ECU part number is correct (make sure a dummy part is not connected)

-

Check the software version of the radio and display receiver assembly and the navigation ECU. If a newer version is available, update the software version and check the symptoms again.

-

Follow the "Start Signal Circuit between Radio Receiver Assembly and Navigation ECU" procedure

Wire harness or connector (radio and display receiver assembly - navigation ECU)

-

Navigation ECU

Radio and Display Receiver Assembly

Display Function

Symptom

Suspected Area

Link

Black screen (no image appears on the navigation/audio screen)

Follow the "Black Screen" procedure

Follow the "Check Software Error History" procedure in the operation check

If the rear view is displayed normally on the radio and display receiver assembly when the engine is running and the shift lever is in R, replace the radio and display receiver assembly

Radio and Display Receiver Assembly

The display does not dim (does not switch to night mode) when the TAIL switch is in the ON position

Follow the "Display Illumination Does Not Dim When Illumination Control Switch Is ON" procedure

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

The power does not turn off (the screen stays on)

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

The screen is distorted

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Screen flickering or color distortion

Follow the "Screen Flickering or Color Distortion" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Navigation function switches can be operated while the vehicle is being driven

Follow the "Parking Brake Switch Circuit" procedure

Navigation ECU

Radio and Display Receiver Assembly

Unable to cancel Valet Mode

Perform the "Valet Mode Deactivation" section in the Operation Check

Radio and Display Receiver Assembly

General audio function

Symptom

Suspected Area

Link

The system does not operate when the power switch is pressed.

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

No sound comes from the speakers

Follow the "No Sound from Speakers" procedure

Follow the "Mute Signal Circuit between Radio and DCM (Telematics Transceiver)" procedure

Follow the "Speaker Circuit" procedure

DCM (Telematics Transceiver)

Radio and Display Receiver Assembly

Abnormal noise is present

Follow the "Noise Interference" procedure

DCM (Telematics Transceiver)

Radio and Display Receiver Assembly

Sound quality is poor in all modes (volume is too low).

Make sure the ASL function is turned off

-

Follow the "Poor Sound Quality in All Modes (Low Volume)" procedure

Follow the "Mute Signal Circuit between Radio and DCM (Telematics Transceiver)" procedure

Follow the "Speaker Circuit" procedure

DCM (Telematics Transceiver)

Radio and Display Receiver Assembly

ASL does not operate

Make sure the ASL function is turned on

-

Radio and Display Receiver Assembly

Panel switch and touch screen switch function

Symptom

Suspected Area

Link

Panel switch illumination does not operate when the TAIL switch is in the ON position

Follow the "Panel Switch Illumination Does Not Operate When TAIL Switch Is ON" procedure

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

Panel switches do not operate

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Touch screen buttons do not operate

Follow the "Touch Screen Switches Do Not Operate" procedure

Follow the "Radio Receiver Power Supply Circuit" procedure

Radio and Display Receiver Assembly

Steering wheel switch function

Symptom

Suspected Area

Link

The system cannot be activated using the steering wheel switch

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Steering Wheel Switch Circuit" procedure

Radio and Display Receiver Assembly

Steering wheel switch illumination does not operate when the tail light switch is in the ON position

Follow the "Illumination Circuit" procedure

Radio and Display Receiver Assembly

Navigation Function

Symptom

Suspected Area

Link

The "No GPS signal" icon is displayed

Follow the ""No GPS signal"" Icon Is Displayed" procedure

Navigation Cable No. 1

Antenna Cable Sub-assembly

Navigation antenna assembly

Navigation ECU

The date and time on the navigation screen differ from the actual date and time

Follow the ""No GPS signal"" Icon Is Displayed" procedure

Navigation Cable No. 1

Antenna Cable Sub-assembly

Navigation antenna assembly

Navigation ECU

The vehicle position marker deviates from the correct position and does not return to the correct position

Follow the ""No GPS signal"" Icon Is Displayed" procedure

Follow the "Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter" procedure

Navigation Cable No. 1

Antenna Cable Sub-assembly

Navigation antenna assembly

Navigation ECU

The cursor or map rotates while the vehicle is stopped

Follow the "The cursor or map rotates while the vehicle is stopped" procedure

Navigation ECU

The vehicle position marker moves in the opposite direction of the vehicle

Follow the "The cursor or map rotates while the vehicle is stopped" procedure

Perform the "Vehicle Signal Check" in the Operation Check

Follow the "Reverse Signal Circuit" procedure

Follow the "Reverse Signal Circuit between Radio Receiver Assembly and Navigation ECU" procedure

Navigation ECU

The vehicle position marker deviates from the correct position and repeatedly returns to it, even though the "No GPS signal" icon is not displayed.

Follow the ""No GPS signal"" Icon Is Displayed" procedure

Follow the "Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter" procedure

Drive the vehicle during sensor learning (in an area where GPS signals can be received, drive the vehicle clockwise and counterclockwise in a loop of at least 200 meters, at least 2 times)

-

Navigation Cable No. 1

Antenna Cable Sub-assembly

Navigation antenna assembly

Navigation ECU

The vehicle position marker moves slowly or quickly

Follow the ""No GPS signal"" Icon Is Displayed" procedure

Follow the "Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter" procedure

Navigation Cable No. 1

Antenna Cable Sub-assembly

Navigation antenna assembly

Navigation ECU

Voice guidance does not operate.

Follow the "Voice Guidance Does Not Operate" procedure

Follow the "Speaker Circuit" procedure

DCM (Telematics Transceiver)

Navigation ECU

Radio and Display Receiver Assembly

Incomplete map display

Navigation ECU

Unable to calculate route

Follow the "Unable to Calculate Route" procedure

Navigation ECU

The navigation system cannot store the point in memory or store the settings for each item

Navigation ECU

A message asking you to wait due to low temperature is displayed

Start the engine and raise the cabin temperature (near the navigation ECU)

-

Navigation ECU

A message is displayed because map data cannot be read, and the current position screen is not displayed

If the message appears only while the vehicle is driving on rough roads, check whether the message disappears when the vehicle is stopped

-

Navigation ECU

The map screen turns white or blue (the GPS reception status is displayed normally, and the switches and the own vehicle position marker are also displayed normally)

Change the map scale to the smallest value (scale that shows a wide area)

-

Navigation ECU

Weather and traffic information cannot be obtained

Check the service and traffic information update settings

-

Follow the "Weather and Traffic Information Cannot Be Obtained" procedure

Radio and Display Receiver Assembly

The weather and traffic information obtained differs from the actual weather and traffic conditions, or is inaccurate.

Change the time zone and search again.

-

Change the vehicle location and search again.

-

Customizable settings cannot be changed. (Customizable settings can be changed using the Techstream.)

Radio and Display Receiver Assembly

The reverse signal does not change in Check Vehicle Signal mode.

Follow the "Reverse Signal Circuit" procedure

Radio and Display Receiver Assembly

The parking brake switch signal does not change in the vehicle signal check mode

Follow the "Parking Brake Switch Circuit" procedure

Radio and Display Receiver Assembly

FM or AM radio operation

Symptom

Suspected Area

Link

Radio broadcasts cannot be received or reception is poor.

Follow the "Radio Broadcasts Cannot Be Received or Reception Is Poor" procedure

Radio broadcasts can be received but the station name is not displayed (some radio stations do not provide the same information)

Radio and Display Receiver Assembly

Radio broadcasts can be displayed but cannot be heard through the speakers

Operate the volume switch and increase the volume.

-

Radio and Display Receiver Assembly

After setting the hands-free or voice recognition function to OFF, the radio mute function does not operate

Make sure the radio mute setting is turned ON

-

Radio and Display Receiver Assembly

When the radio mute function operates, the sound is interrupted, cannot be heard, or sound quality is poor

Check whether similar symptoms occur when receiving conventional FM/AM broadcasts

-

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

When the radio mute function operates, sound can be heard but no information is displayed (some radio stations do not provide their station identification information).

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

HD Radio Operation

Symptom

Suspected Area

Link

Only "HD Radio" stations cannot be listened to or selected, or the digital or analog sound cannot be switched

Check the "HD Radio" settings

-

Radio and Display Receiver Assembly

When HD Radio is on, the album cover is not displayed

When a song not registered in Gracenote CDDB is playing, or when album cover information is not provided by the radio station, its album cover is not displayed

-

When HD Radio is on, the album cover is not displayed

Radio and Display Receiver Assembly

The radio station logo cannot be displayed

Check whether similar symptoms occur when receiving other broadcasts

-

Check whether similar symptoms occur with another vehicle

-

Radio and Display Receiver Assembly

The SPS channel cannot be selected

Make sure that the FM HD Radio mode is selected

-

After selecting "Refresh", make sure the SPS channel is in the station list

-

Radio and Display Receiver Assembly

When the SPS channel is selected, the sound cannot be heard

After selecting "Refresh", select the SPS channel from the station list

-

Radio and Display Receiver Assembly

SiriusXM Satellite Radio function (with SXM function)

Symptom

Suspected Area

Link

Satellite radio broadcasts cannot be received or reception is poor

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Pay-per-view satellite radio broadcasts cannot be received

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Satellite radio broadcasts cannot be selected, or after selecting a broadcast, it cannot be stored in memory

Go to the "Satellite radio broadcasts cannot be received" item

Go to the "Satellite radio broadcasts cannot be selected, or after selecting a broadcast, it cannot be stored in memory" item

Radio and Display Receiver Assembly

Satellite radio may be displayed but radio broadcasts cannot be heard from the speakers

Check the volume settings

-

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

The radio station logo cannot be displayed

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

Satellite radio text information cannot be displayed

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

The satellite radio station cannot be selected (scanning cannot be performed)

Go to the "Satellite radio broadcasts cannot be received" item

Radio and Display Receiver Assembly

When satellite radio is on, the album cover is not displayed

When a song not registered in Gracenote CDDB is playing, its album cover is not displayed

-

When satellite radio is on, the album cover is not displayed

Radio and Display Receiver Assembly

After setting the hands-free or voice recognition function to OFF, the radio mute function does not operate

Make sure the radio mute setting is turned ON

-

Radio and Display Receiver Assembly

When the radio mute function operates, the sound is interrupted, cannot be heard, or sound quality is poor

Check whether similar symptoms occur when receiving regular SiriusXM radio broadcasts

-

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

When the audio unit cache is operating, sound is heard but no information is displayed (some radio stations do not provide their station designation information)

Check whether similar symptoms occur when receiving other broadcasts

-

Move the vehicle to a location with good reception and check again

-

Radio and Display Receiver Assembly

AUX function

Symptom

Suspected Area

Link

Auxiliary device sound cannot be heard or sound quality is poor (a stereo jack of the audio system is used)

Follow the "Audio Signal Circuit between Radio and Stereo Jack Adapter" procedure

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

"AUX/VTR" does not appear on the system check mode screen

Follow the "Audio Signal Circuit between Radio and Stereo Jack Adapter" procedure

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

USB Function

Symptom

Suspected Area

Link

The sound from the USB device cannot be heard, or the sound quality is poor. (USB connector is used.)

Follow the procedure "Data Signal Circuit Between Audio Unit and Stereo Jack Adapter"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

The USB device or "iPod" is not recognized

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

Track information such as track name, artist name and album name is not displayed

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

The USB device or "iPod" is recognized but cannot play, or cannot play in a specific order

Check that the designated folder name is used.

-

Make sure the file name contains no more than 32 characters and that a supported language is used.

-

Make sure the file system of the USB device is FAT16 or FAT32.

-

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

Album cover art is not displayed

Check that the album art display on the "Audio" settings screen is set to ON.

-

Make sure a JPEG, BMP or PNG file is used for the album art saved in the music data of the USB device or "iPod".

-

Check whether similar symptoms occur with another vehicle

-

If a Gracenote database update message appears on the album cover screen and update data has been downloaded to the audio and display unit, update the Gracenote database to the latest version.

-

Radio and Display Receiver Assembly

The user-defined cover art cannot be displayed

Make sure the Gracenote database album art priority display setting is set to OFF.

-

Make sure a JPEG, BMP or PNG file is used for the album art saved in the music data of the USB device or "iPod".

-

Radio and Display Receiver Assembly

"iPod" battery cannot be charged

Follow the procedure "USB Audio System Recognition/Playback Error"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

The screen is distorted or not displayed only when using a USB device connected to the Stereo Jack Adapter Assembly.

Check whether a video file is selected in USB mode.

-

Connect a USB device in good condition to the Stereo Jack Adapter Assembly and make sure an image is output.

-

Follow the procedure "Data Signal Circuit Between Audio Unit and Stereo Jack Adapter"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

The screen color is poor only when using a USB device connected to the Stereo Jack Adapter Assembly.

Change the color settings on the display adjustment screen.

-

Follow the procedure "Data Signal Circuit Between Audio Unit and Stereo Jack Adapter"

Stereo Jack Adapter Assembly

Radio and Display Receiver Assembly

Voice recognition function

Symptom

Suspected Area

Link

The voice menu screen is not displayed (voice recognition function is not activated)

Check whether the voice recognition guidance function is set to ON.

-

Follow the "Panel Switches Do Not Operate" procedure

Follow the "Steering Wheel Switch Circuit" procedure

Navigation ECU

Radio and Display Receiver Assembly

When the voice recognition switch is pressed, a short beep sounds but the voice is not recognized correctly

Follow the procedure "Voice Not Recognized"

Follow the procedure "Microphone Circuit"

Navigation ECU

The mobile assistant function does not work.

Check whether the voice recognition application can be used on the device.

-

Make sure the Bluetooth hands-free function operates normally.

-

Follow the "Steering Wheel Switch Circuit" procedure

Follow the "Check Microphone (Input to Radio Receiver and Display Assembly)" procedure in Check Operation.

Radio and Display Receiver Assembly

"Wi-Fi" hotspot function

Symptom

Suspected Area

Link

The "Wi-Fi" connection cannot be established

Check whether the Toyota Entune App Suite function is available

Check the DCM icon on the multi-information display

-

Check the status of the "Wi-Fi" hotspot contract

-

Make sure the "Wi-Fi" hotspot function is turned on

-

Check the status of the "Wi-Fi" hotspot indicator

-

Check whether a "Wi-Fi"-compatible device in good condition can be connected to the vehicle

-

Move the vehicle to an area with few radio wave interferences and remove any accessories likely to cause radio wave interference, then check again

-

Radio and Display Receiver Assembly

Link application function

Symptom

Suspected Area

Link

The Link application function cannot be started (the smartphone battery may need charging)

Make sure the smartphone is compatible with the Link application

-

Check the smartphone settings

-

Check the connection of the smartphone to the radio receiver and display unit

-

Radio and Display Receiver Assembly

The Link application function can be started but no sound can be heard (the smartphone battery may need charging)

Make sure sound can be output from the speakers

-

Make sure sound can be output from the smartphone

-

Make sure the volume is not set to "0"

-

Make sure mute is not selected

-

Check the Link app function using another compatible smartphone

-

Radio and Display Receiver Assembly

"Bluetooth" hands-free function

Symptom

Suspected Area

Link

"Bluetooth" does not work (the in-vehicle unit cannot be found by the mobile phone)

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone cannot be registered

Follow the procedure "Mobile Phone Registration Error"

The "Bluetooth"-compatible mobile phone cannot be connected

Check whether the mobile phone is connected as a hands-free device

-

Move the mobile phone close to the in-vehicle unit and reconnect it

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone cannot connect automatically (can be connected manually)

Make sure the "Bluetooth" auto connection setting on the in-vehicle unit is set to ON

-

Radio and Display Receiver Assembly

The "Bluetooth"-compatible mobile phone connection is disconnected

Move the mobile phone close to the in-vehicle unit and make sure it reconnects

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Another "Bluetooth"-compatible mobile phone is connected to the system

Check the mobile phone connection priority

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Message prompting to check whether the mobile phone is displayed

Move the mobile phone close to the in-vehicle unit and make sure it reconnects

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

When the engine switch is set to ON (ACC), instructions for checking the connection conditions between the mobile phone and the vehicle unit are displayed.

Set the mobile phone connection confirmation display to OFF on the in-vehicle unit

-

Phonebook data cannot be transferred

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to ON

-

Enter "1234" on the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required)

-

Make sure no application is running on the mobile phone

-

When using the "Bluetooth" audio function, disconnect the "Bluetooth" audio player and check operation

-

Transfer the phonebook data manually

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Phonebook data is erased

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to OFF

-

Radio and Display Receiver Assembly

Phonebook data cannot be edited

Make sure the phonebook data automatic transfer setting on the in-vehicle unit is set to OFF

-

Radio and Display Receiver Assembly

All transferred phonebook data is sorted under "Other"

Make sure no application is running on the mobile phone

-

Make sure the phonebook data on the mobile phone is not stored on the SIM card

-

Follow the procedure "Mobile Phone Check"

Explain to the customer that all transferred phonebook data may be stored under "Other" depending on the mobile phone

-

The mobile phone cannot make/receive calls

Move the vehicle to an area with mobile phone reception, check whether the mobile phone is connected to the vehicle via "Bluetooth" technology, and operate the in-vehicle unit again

-

Check that the mobile phone can make and receive outgoing/incoming calls correctly when it is not connected via "Bluetooth"

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The caller's voice is interrupted by noise or sound quality is poor

Check the voice reception volume (if it is too high, the voice may sound distorted)

-

Make a call with the mobile phone disconnected from "Bluetooth" and make sure the caller's voice is clearly audible

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The caller's voice cannot be heard

Check that the voice reception volume is not set to minimum

-

Make a call with the mobile phone disconnected from "Bluetooth" and make sure the caller's voice is clearly audible

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

Your voice (the caller's side) is interrupted by noise or sound quality is poor

Check the voice transmission volume (if it is too high, the voice may sound distorted)

-

Make sure no object can cause noise at the microphone (air outlet from the air conditioning system pointed at the microphone, wind from an open window, additional devices, etc. can affect noise occurrence)

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Follow the procedure "Microphone Circuit"

Radio and Display Receiver Assembly

The other party cannot hear your voice

Make sure the mute button is not set to ON

-

Make sure no object can cause noise at the microphone (air outlet from the air conditioning system pointed at the microphone, wind from an open window, additional devices, etc. can affect noise occurrence)

-

Follow the procedure "Check Hands-Free Conversation Quality Setting" in "Operation Check"

Follow the procedure "Mobile Phone Check"

Follow the procedure "Microphone Circuit"

Radio and Display Receiver Assembly

No notification when a new SMS/MMS/e-mail is received*

Check the SMS/MMS/e-mail notification settings on the mobile phone and on the audio and display unit

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

The received SMS/MMS/e-mail cannot be read*

Check the SMS/MMS/e-mail forwarding settings on the mobile phone and on the Radio Receiver and Display Assembly.

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

It is not possible to reply to the SMS/MMS/e-mail*

Move the vehicle to an area with mobile phone reception, and check the operation of the audio and display unit and the mobile phone

-

Check whether the mobile phone can send an SMS/MMS/e-mail

-

Follow the procedure "Mobile Phone Check"

Radio and Display Receiver Assembly

  • *: With SMS/MMS/e-mail function
"Bluetooth" audio function

Symptom

Suspected Area

Link

The player cannot be registered

Follow the procedure "The portable player cannot be registered"

Radio and Display Receiver Assembly

The player cannot be connected manually/automatically

Follow the procedure "The portable player cannot be registered"

Follow the procedure "The portable player cannot be connected manually/automatically"

Radio and Display Receiver Assembly

A mobile phone with a portable audio player function is not recognized as a "Bluetooth" audio player even when connected via "Bluetooth"

Follow the procedure "The portable player cannot be registered"

Follow the procedure "The portable player cannot be connected manually/automatically"

Radio and Display Receiver Assembly

The portable player sound is not output from the speakers, or the sound is low

Follow the procedure "The portable player sound is not output from the speakers or the sound is low"

Radio and Display Receiver Assembly

The portable player does not play, even after selecting the "Bluetooth" audio mode

Follow the procedure "Does not play even after selecting the Bluetooth mode"

Radio and Display Receiver Assembly

The portable player does not play

Follow the procedure "Does not play even after selecting the Bluetooth mode"

Radio and Display Receiver Assembly

Track information such as track number, track name, elapsed time and playlist is not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

Portable player operation keys such as play, pause, repeat and shuffle are not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

The "Bluetooth" signal status is not displayed

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

The pause, file selection, fast forward, fast reverse and shuffle functions of the portable player are unavailable

Follow the procedure "The portable player cannot be operated using the onboard device or track information is not displayed on the onboard device"

Radio and Display Receiver Assembly

Sudden sound changes or noise during playback using the portable player

Follow the procedure "Sudden sound changes or noise during playback using the portable player"

Radio and Display Receiver Assembly

A registered component can no longer be deleted

Go to the "A registered component can no longer be deleted" item

Radio and Display Receiver Assembly

Software Update Function

Symptom

Suspected Area

Link

"The software update cannot be started because the media is in use. Please try again when the media is no longer in use." is displayed.

Perform the operation again after listening to music with a USB audio system.

-

Replace the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"Unable to update the software. Please try again later." is displayed.

The software update may sometimes fail because a device or communication medium is still being prepared, such as when updating right after the navigation system is started. In this case, wait a while and then perform the operation.

-

Check with the service center whether there are problems with the downloaded software.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"Unable to get new software because the line is busy. Please try again later." is displayed.

Perform this operation after some time.

-

End other functions that use communication, then perform this operation again.

-

Check the operating conditions with the service center.

-

Check with the service center whether there is a problem with the transmission log to the device.

-

Perform the software update again using communication*.

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"Software update service finished." is displayed.

Check with the service center whether the device is a production-released unit.

-

Check with the service center whether there is a problem with the transmission log to the device.

-

Check with the service center whether the Model ID verified on the software update screen and the Model ID sent by the device are the same.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is a software update. Please contact your dealer." or a similar message is displayed.

Check with the service center whether there is a problem with the transmission log to the device.

-

Perform the software update again using communication*.

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is a software update. Please perform update with a PC." or a similar message is displayed.

Check with the service center whether the size of the software the device is trying to update can be sent by the DCM (telematics transceiver)*. If it cannot be sent, perform the software update using a USB storage device.

-

Check with the service center whether there is a problem with the transmission log to the device.

-

Perform the software update again using communication*.

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is no new software or the media is not inserted." is displayed.

Check whether the USB memory with the new software saved is connected to the USB connector.

-

Check the Model ID on the software update screen and confirm that it matches the file name of the downloaded software.

-

Download the software again using a PC, copy it to a USB memory, and perform the software update.

-

Check with the service center whether there are problems with the downloaded software.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is a problem with the downloaded data. Please try again later." is displayed.

Check with the service center whether there are problems with the downloaded software.

-

Perform the software update again using communication*.

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"New software is not compatible with the system." is displayed.

Check with the service center whether there are problems with the downloaded software.

-

Download the software again using a PC, copy it to a USB memory, and perform the software update.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"The combination of update files is abnormal. Please download it again" or a similar message is displayed.

Check with the service center whether there are problems with the downloaded software.

-

Perform the software update again using communication*.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is a problem with the downloaded data. Please contact your dealer." is displayed.

Perform the software update using communication*.

-

Perform the software update using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"New software is not compatible with the system. Contact your dealer." is displayed.

Perform the software update using communication*.

-

Perform the software update using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"Software could not be updated. Please contact your dealer." is displayed.

Check with the service center whether the Model ID verified on the software update screen and the Model ID sent by the device are the same.

-

Check with the service center whether there are problems with the downloaded software.

-

Check with the service center whether there is a problem with the transmission log to the device.

-

Perform the software update again using communication*.

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

"There is insufficient free space. Please contact your dealer." appears

Perform the software update again using communication*.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

The software update could not be performed using the communication

Follow the instructions when a message appears on the screen

-

Make sure "Check with service center" appears and that the USB memory is not connected to the USB port

-

Explain to the customer that the latest software update is being downloaded when the message "New software is downloading" appears

-

Explain to the customer that the latest software update is being installed when the message "New software is installing" appears

-

Check whether the telematics system operates normally

-

Perform the software update again using the communication

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

The software update could not be performed using the USB memory

Follow the instructions when a message appears on the screen

-

Make sure "Perform software update" is displayed and check whether the USB memory with the new software saved is connected to the USB port

-

Explain to the customer that the latest software update is being downloaded when the message "New software is downloading" appears

-

Explain to the customer that the latest software update is being installed when the message "New software is installing" appears

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If there is audio system software update data but the software update cannot be performed, replace the Radio Receiver and Display Assembly.

Update information cannot be checked when attempting a software update using the communication

Explain to the customer that "Update information" does not appear on the software update screen when the software is up to date

-

Perform the software update using a USB memory, as a software update using the communication is not possible when a message other than "Current software is up to date. There is no need to update" appears when "Check with service center" is selected

-

Check with the service center whether there are problems with the downloaded software.

-

Perform the software update again using the communication

-

Perform the software update again using the USB memory.

-

If there is navigation software update data but the software update cannot be performed, replace the Navigation ECU.

If the audio software update information cannot be checked, replace the radio and display receiver assembly

The software update version display or the update information screen display is normal

Check with the service center whether there are problems with the downloaded software.

-

Perform the software update again using the communication

-

Perform the software update again using the USB memory.

-

If the navigation software update information cannot be checked, replace the navigation ECU

If the audio system version display is not normal, replace the radio and display receiver assembly

The update information date is not displayed

The update information date is not displayed when GPS is not received, so check that the "No GPS Signal" indicator is not displayed

-

As the date may not be recorded when the software update was performed without receiving GPS, check with the customer whether the software update was performed in a place with poor GPS reception, such as an underground parking garage.

-

Wait for the next software update

-

The software update history is erased

Explain to the customer that the history was erased when "Delete Personal Data" is selected on the setting screen

-

Explain to the customer that the history was erased from oldest to newest when at least 20 histories are stored.

-

Wait for the next software update, and replace the navigation ECU if the symptom reoccurs

ECO information function

Symptom

Suspected Area

Link

Information is not displayed or not updated on the "Trip Information" screen.

Set the engine switch to ON (IG) and check again

-

Check whether the SFI system operates normally

Navigation ECU

Information is not displayed or not updated on the "History" screen.

Set the engine switch to ON (IG) and check again

-

Make sure the meter and gauge system operates normally

-

Navigation ECU

The "Fuel Consumption" icon is dimmed.

Check whether other icons or items displayed on the screen have problems

-

Navigation ECU

The graph is not displayed on the "Trip Information" screen

Check again with the engine running

-

Check whether the SFI system operates normally

Navigation ECU

The cruise control range is not displayed on the "Trip Information" screen

Set the engine switch to ON (IG) and check again

-

Navigation ECU

The graph is not updated on the "History" screen even when "Clear" is selected

Set the engine switch to ON (IG) and check again

-

Navigation ECU

The graph is not displayed on the "History" screen

Set the engine switch to ON (IG) and check again

-

Navigation ECU