Navigation / Multi-Display

Expansion Module 2 Disconnected (B1543)

~5min read

DESCRIPTION

If the radio and display receiver assembly cannot detect the navigation ECU for a certain period (90 seconds) after the ignition switch is turned to ON (ACC), and the radio and display receiver assembly confirms the absence of the information by checking the navigation ECU's previous recognition data (stored information), this DTC is stored.

HINT:

The navigation system uses USB communication between devices. If there is an open, a short to +B, or a short to ground in the USB circuit, communication is interrupted and the navigation system will not operate normally.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1543

Expansion module 2 disconnected

Navigation ECU is disconnected

  • Navigation ECU
  • Radio and Display Receiver Assembly
  • Navigation Cable No. 1
  • Antenna Cable Sub-assembly
  • Wire harness or connector

HINT:

This DTC may be stored due to environmental factors such as noise or interference, for example.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts replaced during vehicle inspection or maintenance, initialization, registration or calibration may be required. Refer to the precautions for the navigation system.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • When replacing the radio and display receiver assembly or the navigation ECU, always replace it with a new part. If a radio and display receiver assembly or navigation ECU previously installed on another vehicle is reused, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly or navigation ECU may not operate correctly.

PROCEDURE

  1. CHECK MAP SCREEN

(a) Turn the ignition switch to ON (ACC) and wait 90 seconds.

(b) Press the "MAP" switch and check whether the map screen operates normally.

Result:

Result

Proceed to

The map screen displays normally

A

The map screen does not display normally

B

HINT:

  • This DTC may be stored due to environmental factors such as noise or interference, for example.
  • Clear the past DTCs when the map screen displays normally. (Codes stored due to past environmental factors)
A

USE SIMULATION METHOD TO CHECK

B
  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the engine switch off.

(c) Turn the engine switch on (IG) and wait 90 seconds.

(d) Check the DTCs again and make sure no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK WIRE HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)

(a) Disconnect the connector from the navigation ECU.

*a

Front view of wire harness side connector

(to navigation ECU)

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F135-23 (GND) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F135-10 (+B) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK NAVIGATION CABLE NO. 1

*a

Front view of wire harness side connector

(to navigation ECU)

*b

Front view of wire harness side connector

(to antenna cable sub-assembly)

(a) Disconnect connector UA of the No. 1 navigation cable from the antenna cable sub-assembly.

(b) Disconnect connector GU of the No. 1 navigation cable from the navigation ECU.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

GU-4 (USB+) - UA-1

Always

Below 1 Ω

GU-5 (USB-) - UA-2

Always

Below 1 Ω

GU-6 (USBG) - UA-3

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE ANTENNA CABLE SUB-ASSEMBLY

(a) Replace the antenna cable sub-assembly with a new or normally functioning one.

Click here

NEXT
  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Check DTCs again and confirm that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

END (ANTENNA CABLE SUB-ASSEMBLY WAS FAULTY)

NG
  1. REPLACE NAVIGATION ECU

(a) Replace the navigation ECU with a new one.

Click here

NEXT
  1. CHECK DTCs

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Turn the engine switch off.

(c) Turn the engine switch on (IG) and wait 90 seconds.

(d) Check the DTCs again and make sure no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTC is output.

OK

END (NAVIGATION ECU IS FAULTY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY