System Description
SYSTEM DESCRIPTION
DESCRIPTION
(a) The Safety Connect system provides the following services: ACN (Automatic Collision Notification), manual emergency call, stolen vehicle tracking, and roadside assistance, through data and voice communication between the vehicle and the call center via a mobile phone network. As shown in the illustration, when a collision is detected, the vehicle sends its location, calculated based on GPS signals, and the DCM (Telematics Transceiver) identification code to a call center. Once the necessary information has been gathered, the call center relays this information to emergency services.
*: Public Safety Answering Point
SYSTEM OPERATION
(a) ACN (Automatic Collision Notification)
(1) When a collision is detected, the vehicle automatically connects to the call center and reports the vehicle location and information via data communication. The operator then connects to the vehicle and communicates with the occupant. Even if the occupant does not respond, the operator can notify emergency services.
(b) Manual Emergency Call
(1) After pressing the manual (SOS) switch, the occupant can speak with an operator at the call center and request assistance.
(c) Stolen Vehicle Locating
(1) Once the vehicle theft has been reported to the police, the customer can contact the call center to start the stolen vehicle locating process. The operator locates the vehicle by GPS and provides the information to the police.
(d) Roadside Assistance
(1) Press the manual SOS switch to contact the call center and access a wide range of services, such as towing, flat tire assistance, fuel delivery, etc.
*: Public Safety Answering Point
HINT:
The shape of the manual SOS switch shown in the illustration is an example and may differ from the actual vehicle.
VOICE GUIDANCE FUNCTION
HINT:
The voice system announces the following voice prompts in the situations shown.
Voice prompt | Operating condition |
|---|---|
Communication module malfunction detected. Please contact your dealer. |
When the system detects a malfunction of the LED (red only) and another DTC is stored. The message is announced each time the ignition switch is turned to ON until the problem is resolved. |
Connecting to the Call Center. |
Start of DCM activation. |
Communication module activation failed. |
DCM activation fails for any reason. |
Communication module activation completed. |
DCM activation has been completed successfully. |
If you continue to receive this message, contact your dealer. |
Follows the activation sequence. |
Unable to Connect to the Call Center. |
- |
Impact detected. |
When the DCM (Data Communication Module) receives a collision detection signal. |
Connecting to the Emergency Call Center. |
Call initiated with the call center. |
Unable to Connect to the Emergency Call Center. |
The DCM (Data Communication Module) cannot connect to the emergency call center for any reason. |
To cancel, please press the button again. |
To end the call manually. |
Emergency call canceled. |
Confirmation that the call has been canceled. |
The system will try again. |
Unable to connect to the call center. |
To activate, please press the button again within 5 seconds. |
This voice prompt gives the instruction for activation. |
Safety Connect is not active. |
When the DCM (Data Communication Module) is in inactive mode. |
To subscribe to the service, call 1-855-405-6500 and a representative will assist you. |
When the DCM (Data Communication Module) is in inactive mode. |
DESCRIPTION OF THE BUB (BACK-UP BATTERY)
(a) When an ACN (Automatic Collision Notification) occurs, the BUB (Back-Up Battery) supplies power to the DCM (Data Communication Module).
NOTICE:
- After the ACN has been performed, the BUB (Back-Up Battery) must be replaced.
- The BUB (Back-Up Battery) must not be replaced while an ACN call is in progress.
HINT:
When a manual emergency call is made, the BUB (Back-Up Battery) is not used as a power source.
(b) When the BUB (Back-Up Battery) needs to be replaced, the red indicator on the manual SOS switch illuminates. The DCM (Data Communication Module) also stores a DTC.
INDICATOR CONTROL FUNCTION DURING DCM (DATA COMMUNICATION MODULE) SELF-DIAGNOSIS MODE
HINT:
Each time the ignition switch is turned to ON (IG), the DCM (Data Communication Module) enters self-diagnosis mode. The red indicator on the manual SOS switch illuminates for 2 seconds and then turns off, after which the green indicator on the manual SOS switch illuminates and stays on under normal operating conditions. The following table shows the possible situations.
- *: If a call is in progress and the ignition switch is in OFF, the call will continue and the LED function will not change.
CONTRACT MODE CHANGES
Contract mode | Description |
|---|---|
Transport mode |
Mode the DCM (Data Communication Module) is in when leaving the factory and during transport. In this mode, when the ignition switch is turned to ON, the system automatically attempts to activate provisioning mode. |
Provisioning mode |
This mode starts once the vehicle is automatically activated (in provisioning mode) after arriving at its destination or after being left on the production line. ACN and stolen vehicle locator services are available. |
Active mode |
This mode starts when the owner's information is transmitted to the telematics service provider and the customer signs a contract for the Safety Connect system. All Safety Connect system functions are available. |
Service mode |
This mode applies to the DCM (Data Communication Module) of a replacement part that has not been activated after replacing the vehicle's DCM (Data Communication Module). The DCM (Data Communication Module) has no associated phone number. |
Inactive mode |
This mode occurs when the Safety Connect subscription has been cancelled. |