Mobile Communication

Telephone microphone malfunction (B1572)

~3min read

DESCRIPTION

This DTC is output when the DCM (telematics transceiver) detects a malfunction in the telephone microphone assembly circuit.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1572

Telephone Microphone Malfunction

MCVD current meets the malfunction criteria for 10 seconds while the ignition switch is ON.

  • Wire harness or connector
  • Map light assembly (telephone microphone assembly)
  • DCM (Telematics Transceiver)

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

HINT:

Before performing this diagnostic procedure, make sure to perform the status check and make sure that the DCM/VIN registration information is correct.

Click here

PROCEDURE

  1. CHECK DTCs

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON and wait for 10 seconds.

(d) Turn on the Techstream.

(e) Clear the DTCs.

Body Electrical > Telematics > Clear DTCs

(f) Check the DTCs again.

Body Electrical > Telematics > Trouble Codes

Result:

Result

Proceed to

DTC B1572 is output

A

DTC B1572 is not output

B

B

CHECK FOR INTERMITTENT PROBLEMS

A
  1. CHECK READING LIGHT ASSEMBLY (POWER SOURCE OF TELEPHONE MICROPHONE ASSEMBLY)

(a) Remove the reading light assembly (telephone microphone assembly), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(Map light assembly (telephone microphone assembly))

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

R2-9 (MACC) - Body ground

Ignition Switch in ACC position

4 à 6 V

Standard resistance:

Tester Connection

Condition

Specified Condition

R2-7 (MCO-) - Body ground

Always

Below 1 Ω

NG

GO TO STEP 4

OK
  1. CHECK HARNESS AND CONNECTOR (DCM (DATA COMMUNICATION MODULE) - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

(a) Disconnect connector F134 from the DCM (Data Communication Module).

(b) Disconnect connector R2 from the map light assembly (telephone microphone assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-34 (MIC+) - R2-8 (MCO+)

Always

Below 1 Ω

F134-34 (MIC+) or R2-8 (MCO+) - Body Ground

Always

10 kΩ minimum

F134-35 (MIC-) - R2-7 (MCO-)

Always

Below 1 Ω

F134-35 (MIC-) or R2-7 (MCO-) - Body Ground

Always

10 kΩ minimum

F134-32 (SGND) - Body Ground

Always

10 kΩ minimum

OK

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK DCM (TELEMATICS TRANSCEIVER) (POWER SOURCE OF TELEPHONE MICROPHONE ASSEMBLY)

(a) Remove the DCM (telematics transceiver), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F134-33 (MCVD) - Body Ground

Ignition Switch in ACC position

4 à 6 V

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-35 (MCI-) - Body ground

Always

Below 1 Ω

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG
  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION