Mobile Communication

Manual (SOS) Switch Red Indicator Malfunction (B1570)

~6min read

DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects an open or short circuit in the manual (SOS) switch red indicator.

The manual (SOS) switch red indicator lights for 2 seconds when the ignition switch is turned ON, and then goes off. If a malfunction is detected in the emergency call system, the manual (SOS) switch red indicator remains on.

However, the manual (SOS) switch red indicator may not light up when this DTC is output.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1570

Manual (SOS) Switch Red Indicator Malfunction

The current of the manual (SOS) switch red indicator reaches the malfunction criteria for 10 seconds when the ignition switch is ON.

  • Emergency Call Switch Assembly (manual (SOS) switch)
  • Reading Light Assembly
  • Wire harness or connector
  • DCM (Telematics Transceiver)

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

HINT:

  • Before performing this diagnostic procedure, make sure to perform the status check and make sure that the DCM/VIN registration information is correct.

    Click here

  • The manual (SOS) switch red indicator may not operate to indicate that another DTC has been output, therefore voice guidance is output.

PROCEDURE

  1. CHECK DTCs

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON and wait for 10 seconds.

(d) Turn on the Techstream.

(e) Clear the DTCs.

Body Electrical > Telematics > Clear DTCs

(f) Check the DTCs again.

Body Electrical > Telematics > Trouble Codes

Result:

Result

Proceed to

DTCs B1570, B1571 and B15C5 are output

A

DTC B1570 is output (DTCs B1571 and B15C5 are not output)

B

B

GO TO STEP 6

A
  1. CHECK READING LIGHT ASSEMBLY (RED INDICATOR)

(a) Disconnect the R4 connector from the reading light assembly.

*a

Component without wire harness connected

(reading light assembly)

(b) Connect 2 dry cells (1.5 V each) in series.

(c) Connect the positive (+) battery cable to terminal 6 (IND1) and the negative (-) cable to terminal 1 (GND3) of the reading light assembly connector.

(d) Check whether the manual (SOS) switch red indicator lights up.

OK:

The red indicator light comes on.

NG

GO TO STEP 5

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - READING LIGHT ASSEMBLY)

(a) Disconnect connector F134 from the DCM (Data Communication Module).

(b) Disconnect connector R4 from the map light assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-26 (SIG-) - R4-1 (GND3)

Always

Below 1 Ω

F134-26 (SIG-) or R4-1 (GND3) - Body ground

Always

10 kΩ minimum

F134-11 (IND1) - R4-6 (IND1)

Always

Below 1 Ω

F134-11 (IND1) or R4-6 (IND1) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION

  1. INSPECT EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

(a) Remove the emergency switch assembly (manual (SOS) switch).

Click here

(b) Inspect the emergency switch assembly (manual (SOS) switch).

Click here

OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPLACE EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

  1. CHECK SOS SWITCH ASSEMBLY (MANUAL SOS RED INDICATOR LIGHT SWITCH POSITION)

(a) Check the red indicator light condition after turning the ignition switch to ON.

Click here

Result:

Result

Proceed to

The red indicator light does not come on.

A

The red indicator light stays on.

B

B

GO TO STEP 12

A
  1. CHECK READING LIGHT ASSEMBLY (RED INDICATOR LIGHT INPUT VOLTAGE)

(a) Remove the map light assembly, but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(reading light assembly)

(b) Connect the positive (+) lead of a voltmeter to terminal R4-6 (IND1) and the negative (-) lead to terminal R4-1 (GND3).

(c) Measure the voltage.

Standard:

1.0 to 8.5 V, 2 seconds after the ignition switch is turned to ON.

0 V when the ignition switch is OFF.

NG

GO TO STEP 9

OK
  1. INSPECT EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

(a) Remove the emergency switch assembly (manual (SOS) switch).

Click here

(b) Inspect the emergency switch assembly (manual (SOS) switch).

Click here

OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPLACE EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

  1. CHECK DCM (TELEMATICS TRANSCEIVER) (RED INDICATOR LIGHT OUTPUT VOLTAGE)

(a) Remove the DCM (telematics transceiver), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(b) Connect the positive (+) lead of a voltmeter to terminal F134-11 (IND1) and the negative (-) lead to body ground.

(c) Measure the voltage.

Standard:

1.0 to 8.5 V, 2 seconds after the ignition switch is turned to ON.

0 V when the ignition switch is OFF.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG
  1. INSPECT WIRE HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND)

(a) Remove the DCM (telematics transceiver), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-11 (IND1) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.

Click here

NEXT

PERFORM DCM ACTIVATION

  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION