Mobile Communication

Manual (SOS) Switch Green Indicator Malfunction (B1571)

~6min read

DESCRIPTION

This DTC is stored when the DCM (telematics transceiver) detects an open or short circuit in the manual (SOS) switch green indicator. The manual (SOS) switch green indicator turns on after the ignition switch is turned ON.

If the safety connect system is not active, the manual (SOS) switch green indicator turns off.

If the safety connect system is active, the manual (SOS) switch green indicator flashes during communication with the call center.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

B1571

Manual (SOS) Switch Green Indicator Malfunction

The current of the manual (SOS) switch green indicator reaches the malfunction threshold for 10 seconds when the ignition switch is ON.

  • Emergency Call Switch Assembly (manual (SOS) switch)
  • Reading Light Assembly
  • Wire harness or connector
  • DCM (Telematics Transceiver)

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

HINT:

Before performing this diagnostic procedure, make sure to perform the status check and make sure that the DCM/VIN registration information is correct.

Click here

PROCEDURE

  1. CHECK DTCs

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON and wait for 10 seconds.

(d) Turn on the Techstream.

(e) Clear the DTCs.

Body Electrical > Telematics > Clear DTCs

(f) Check the DTCs again.

Body Electrical > Telematics > Trouble Codes

Result:

Result

Proceed to

DTCs B1570, B1571 and B15C5 are output

A

DTC B1571 is output

(DTCs B1570 and B15C5 are not output)

B

B

GO TO STEP 6

A
  1. INSPECT READING LIGHT ASSEMBLY (GREEN INDICATOR)

(a) Disconnect the R4 connector from the reading light assembly.

*a

Component without wire harness connected

(reading light assembly)

(b) Connect 2 dry cells (1.5 V each) in series.

(c) Connect the positive (+) battery lead to terminal 5 (IND2) and the negative (-) lead to terminal 1 (GND3) of the reading light assembly connector.

(d) Check whether the manual (SOS) switch green indicator light turns on.

OK:

The green indicator light comes on.

NG

GO TO STEP 5

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - READING LIGHT ASSEMBLY)

(a) Disconnect connector F134 from the DCM (Data Communication Module).

(b) Disconnect connector R4 from the map light assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-26 (SIG-) - R4-1 (GND3)

Always

Below 1 Ω

F134-26 (SIG-) or R4-1 (GND3) - Body ground

Always

10 kΩ minimum

F134-12 (IND2) - R4-5 (IND2)

Always

Below 1 Ω

F134-12 (IND2) or R4-5 (IND2) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION

  1. INSPECT EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

(a) Remove the emergency switch assembly (manual (SOS) switch).

Click here

(b) Inspect the emergency switch assembly (manual (SOS) switch).

Click here

OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPLACE EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

  1. INSPECT EMERGENCY SWITCH ASSEMBLY (SOS (MANUAL) SWITCH GREEN INDICATOR STATUS)

(a) Check the green indicator status after the ignition switch is turned to ON.

Click here

Result:

Result

Proceed to

The green indicator stays off

A

The green indicator stays on

B

B

GO TO STEP 12

A
  1. INSPECT MAP LIGHT ASSEMBLY (GREEN INDICATOR INPUT VOLTAGE)

(a) Remove the map light assembly, but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(reading light assembly)

(b) Connect the positive (+) voltmeter lead to terminal R4-5 (IND2) and the negative (-) lead to terminal R4-1 (GND3).

(c) Measure the voltage.

Standard:

Standard: 1.0 to 8.5 V 2 seconds after the ignition switch is turned ON and the red indicator turns OFF.

0 V when the ignition switch is OFF.

NG

GO TO STEP 9

OK
  1. INSPECT EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

(a) Remove the emergency switch assembly (manual (SOS) switch).

Click here

(b) Inspect the emergency switch assembly (manual (SOS) switch).

Click here

OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPLACE EMERGENCY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

  1. INSPECT DCM (TELEMATICS TRANSCEIVER) (GREEN INDICATOR OUTPUT VOLTAGE)

(a) Remove the DCM (telematics transceiver), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(b) Connect the positive (+) voltmeter lead to terminal F134-12 (IND2) and the negative (-) lead to body ground.

(c) Measure the voltage.

Standard:

Standard: 1.0 to 8.5 V 2 seconds after the ignition switch is turned ON and the red indicator turns OFF.

0 V when the ignition switch is OFF.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG
  1. INSPECT WIRE HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND)

(a) Remove the DCM (telematics transceiver), but do not disconnect the connectors.

Click here

*a

Component with Wire Harness Connected

(DCM (Data Communication Module))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F134-12 (IND2) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION

  1. REPLACE DCM (DATA COMMUNICATION MODULE)

(a) Replace the DCM (telematics transceiver).

Click here

NOTICE:

  • The ignition switch must be in the OFF position.
  • Do not swap the DCM (telematics transceiver) with a DCM from another vehicle.
NEXT

PERFORM DCM ACTIVATION