Engine

P0031 A/f Sensor 1 Heater

18steps
~108min
4/5difficulty
Done 0 of 18
DTC Description

DTC DETECTION LOGIC

  • Deterioration in A/F sensor 1 heater performance.

  • The current amperage in the A/F sensor 1 heater circuit is out of the normal range.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0031

A/F SEN1 HTR (B1)

(HO2S heater control circuit low bank 1 sensor 1)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from A/F sensor 1 heater to ECM
Threshold An excessively low voltage signal is sent to ECM through the A/F sensor 1 heater
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (The A/F sensor 1 heater circuit is open or shorted.)

  • The A/F sensor 1 heater

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between A/F sensor 1 harness connector and ground.

    A/F sensor 1GroundVoltage
    ConnectorTerminal
    F12 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

A/F sensor 1IPDM E/RContinuity
ConnectorTerminalConnectorTerminal
F12 1 F19 52 Existed

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check harness continuity between A/F sensor 1 harness connector and ECM harness connector.

    A/F sensor 1ECMContinuity
    ConnectorTerminalConnectorTerminal
    F12 2 F78 6 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK A/F SENSOR 1 HEATER

Check A/F sensor 1 heater. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

Component Inspection

CHECK AIR FUEL RATIO (A/F) SENSOR 1

  1. Turn ignition switch OFF.

  2. Disconnect A/F sensor 1 harness connector.

  3. Check resistance between A/F sensor 1 terminals as per the following.

    +−Resistance
    A/F sensor 1
    Terminal
    2 1 1.8 - 2.44 Ω [at 25 °C]
    3

    ∞Ω

    (Continuity should not exist)
    4
    1 3
    4

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).