Engine

P2119 Electric Throttle Control Actuator

22steps
~132min
4/5difficulty
Done 0 of 22
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2119

ETC ACTR-B1

(Throttle actuator control throttle body range/performance)
1 Diagnosis condition —
Signal (terminal) —
Threshold Electric throttle control actuator does not function properly due to the return spring malfunction
Diagnosis delay time —
2 Diagnosis condition —
Signal (terminal) —
Threshold Throttle valve opening angle in fail-safe mode is not in specified range
Diagnosis delay time —
3 Diagnosis condition —
Signal (terminal) —
Threshold ECM detects that the throttle valve is stuck open
Diagnosis delay time —

POSSIBLE CAUSE

  • Electric throttle control actuator

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Electric throttle control actuator

(When electric throttle control actuator does not function properly due to the return spring malfunction:)

ECM controls the electric throttle actuator by regulating the throttle opening around the idle position. The engine speed will not rise more than 2,000 rpm.

(When throttle valve opening angle in fail-safe mode is not in specified range:)

ECM controls the electric throttle control actuator by regulating the throttle opening to 20 degrees or less.

(When ECM detects the throttle valve is stuck open:)

While the Nissan Murano vehicle is being driven, it slows down gradually because of fuel cut. After the vehicle stops, the engine stalls.

The engine can restart in the N or P position, and engine speed will not exceed 1,000 rpm or more.
DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION 1 AND 2

  1. Turn ignition switch ON and wait at least 1 second.

  2. Shift selector lever to the D position and wait at least 3 seconds.

  3. Shift selector lever to the P position.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Turn ignition switch ON and wait at least 1 second.

  6. Shift selector lever to the D position and wait at least 3 seconds.

  7. Shift selector lever to the P position.

  8. Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.

  9. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION 3

  1. Turn ignition switch ON and wait at least 1 second.

  2. Shift selector lever to the D position and wait at least 3 seconds.

  3. Shift selector lever to the N or P position.

  4. Start engine and let it idle for 3 seconds.

  5. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

  1. Turn ignition switch OFF.

  2. Remove the intake air duct. Refer to Removal and Installation.

  3. Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Remove the foreign matter and clean the electric throttle control actuator inside, and then perform throttle valve closed position learning. Refer to Description.

REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

  1. Replace electric throttle control actuator. Refer to Removal and Installation.

  2. Go to Description.

>>

INSPECTION END