Engine

P0327 Ks

13steps
~78min
3/5difficulty
Done 0 of 13
DTC Description

DTC DETECTION LOGIC

  • An excessively low voltage from the sensor is sent to ECM.

  • An excessively high voltage from the sensor is sent to ECM.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0327

KNOCK SEN/CIRC-B1

(Knock sensor 1 circuit low bank 1)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from knock sensor to ECM
Threshold An excessively low voltage from the sensor is sent to ECM
Diagnosis delay time —
P0328

KNOCK SEN/CIRC-B1

(Knock sensor 1 circuit high bank 1)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from knock sensor to ECM
Threshold An excessively high voltage from the sensor is sent to ECM.
Diagnosis delay time —
P0332

KNOCK SEN/CIRC-B2

(Knock sensor 2 circuit low bank 2)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from knock sensor to ECM
Threshold An excessively low voltage from the sensor is sent to ECM
Diagnosis delay time —
P0333

KNOCK SEN/CIRC-B1

(Knock sensor 2 circuit high bank 2)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from knock sensor to ECM
Threshold An excessively high voltage from the sensor is sent to ECM.
Diagnosis delay time —

POSSIBLE CAUSE

P0327

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Knock sensor

P0328

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Knock sensor

P0332

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Knock sensor

P0333

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Knock sensor

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and run it for at least 5 seconds at idle speed.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK KNOCK SENSOR GROUND CIRCUIT

  1. Disconnect knock sensor harness connector and ECM harness connector.

  2. Check the continuity between knock sensor harness connector and ECM harness connector.

    DTCKnock sensorECMContinuity
    BankConnectorTerminalConnectorTerminal
    P0327, P0328 1 F202 2 F78 4 Existed
    P0332, P0333 2 F203 2
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between knock sensor harness connector and ECM harness connector.

    DTCKnock sensorECMContinuity
    BankConnectorTerminalConnectorTerminal
    P0327, P0328 1 F202 1 F78 5 Existed
    P0332, P0333 2 F203 1 9
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK KNOCK SENSOR

Check knock sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning knock sensor. Refer to Exploded View.

Component Inspection

CHECK KNOCK SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect knock sensor harness connector.

  3. Check resistance between knock sensor terminal as per the following.

    Knock sensorResistance
    +-
    Terminals
    1 2 Approx. 532 - 588 kΩ [at 20 °C]

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning knock sensor. Refer to Exploded View.