Engine

U0284 Active Grille Shutter

20steps
~120min
4/5difficulty
Done 0 of 20
DTC Description

DTC DETECTION LOGIC

When ECM cannot receive the engine communication signal from active grille shutter.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U0284

LOST COMM (A/GRLL SHTTR MDL A)

(Lost communication with active grille air shutter module A)
Diagnosis condition Ignition switch ON
Signal (terminal) Engine communication signal
Threshold ECM cannot receive the engine communication signal from active grille shutter
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors (Engine communication line is open or circuit shorted.)

  • Active grille shutter

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Active grille shutter ECM operates active grille shutter to fully-open position.
DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC U0284 is displayed with another DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If another DTC Confirmation Procedure is conducted just before this procedure, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more with ignition switch ON.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U0284 is displayed with another DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect active grille shutter harness connector.

  3. Check the voltage between active grille shutter harness connector and ground as follows.

    +−Condition

    Voltage

    (Approx.)
    Active grille shutter
    ConnectorTerminal
    E238 1 Ground Ignition switch: ON Battery voltage
    Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between active grille shutter harness connector and IPDM E/R harness connector.

    Active grille shutterIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E238 1 F19 52 Existed

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER GROUND CIRCUIT

  1. Turn ignition switch OFF

  2. Check the continuity between active grille shutter harness connector and ground.

    Active grille shutter−Continuity
    ConnectorTerminal
    E238 4 Ground Existed
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK ACTIVE GRILLE SHUTTER INPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ECM harness connector and active grille shutter harness connector.

+–Continuity
ECMActive grille shutter
ConnectorTerminalConnectorTerminal
F79 99 E238 3 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER

Check active grille shutter. Refer to Component Inspection (Active Grille Shutter).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.

Component Inspection (Active Grille Shutter)

CHECK ACTIVE GRILLE SHUTTER

With CONSULT

  1. Start the engine.

  2. Select “ACTIVE GRILLE SHUTTER” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.

  3. Touch “CALIBRTN”.

  4. After the calibration completes, check the operation of active grille shutter as follows.

    ConditionActive grille shutter
    Select “CLOSE” Close → Open
    Select “OPEN” Open → Close

Without CONSULT

  1. Turn ignition switch OFF.

  2. Operate shutter by hands to close position.

  3. Check the operation of active grille shutter as follows.

    ConditionActive grille shutter
    Ignition switch: ON Close → Open

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.