Engine

P0116 Ect Sensor

15steps
~90min
4/5difficulty
Done 0 of 15
DTC Description

DTC DETECTION LOGIC

The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the voltage signal of the ECT sensor is higher/lower than that of other temperature sensors when the engine is started with its cold state.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0116

ECT SEN/CIRC

(Engine coolant temperature sensor 1 circuit range/performance)
A Diagnosis condition —
Signal (terminal) Voltage signal transmitted from ECT sensor to ECM
Threshold The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the voltage signal of the ECT sensor is higher/lower than that of other temperature sensors when the engine is started with its cold state
Diagnosis delay time —
B Diagnosis condition —
Signal (terminal) Voltage signal transmitted from ECT sensor to ECM
Threshold Engine coolant temperature signal from engine coolant temperature sensor does not fluctuate, even when some time has passed after starting the engine with pre-warming up condition.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors (High or low resistance in the ECT sensor circuit)

  • ECT sensor

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

INSPECTION START

Is it necessary to erase permanent DTC?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect ECT sensor harness connector.

  3. Remove ECT sensor. Refer to Exploded View.

  4. Check resistance between ECT sensor terminals by heating with hot water as shown in the figure.

    TerminalsConditionResistance (kΩ)
    1 and 2 Temperature [°C (°F)] 20 (68) 2.37 – 2.63
    50 (122) 0.68 – 1.00
    90 (194) 0.236 – 0.260

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, do not add fuel.

  • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.

  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Move the Nissan Murano vehicle to a cool place.

  2. Turn ignition switch OFF and leave the Nissan Murano vehicle for 12 hours.

  3. Start engine and let it idle for 20 minutes or more.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR

Check ECT sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace ECT sensor. Refer to Exploded View.

Component Inspection

CHECK ENGINE COOLANT TEMPERATURE SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect engine coolant temperature sensor harness connector.

  3. Remove engine coolant temperature sensor. Refer to Exploded View.

  4. Check resistance between engine coolant temperature sensor terminals as per the following.

ECT sensorConditionResistance (kΩ)
+−
Terminal
1 2 Temperature [°C (°F)] 20 (68) 2.37 - 2.63
50 (122) 0.68 - 1.00
90 (194) 0.236 - 0.260

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace engine coolant temperature sensor. Refer to Exploded View.