Engine

P0197 Eot Sensor

16steps
~96min
4/5difficulty
Done 0 of 16
DTC Description

DTC DETECTION LOGIC

  • An excessively low voltage from the sensor is sent to ECM.

  • An excessively high voltage from the sensor is sent to ECM.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0197

EOT SEN/CIRC

(Engine oil temperature sensor circuit low)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from engine oil temperature sensor to ECM
Threshold An excessively low voltage from the sensor is sent to ECM
Diagnosis delay time —
P0198

EOT SEN/CIRC

(Engine oil temperature sensor circuit high)
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from engine oil temperature sensor to ECM
Threshold An excessively high voltage from the sensor is sent to ECM
Diagnosis delay time —

POSSIBLE CAUSE

P0197

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Engine oil temperature sensor

P0198

  • Harness or connectors (The sensor circuit is open or shorted.)

  • Engine oil temperature sensor

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Engine oil temperature sensor Intake valve timing control does not function.
DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK EOT SENSOR POWER SUPPLY

  1. Disconnect engine oil temperature (EOT) sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between EOT sensor harness connector and ground.

    EOT sensorGroundVoltage
    ConnectorTerminal
    F68 3 Ground Approx. 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK EOT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between EOT sensor harness connector and ECM harness connector.

    EOT sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    F68 1 F78 15 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK ENGINE OIL TEMPERATURE SENSOR

Check engine oil temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace engine oil temperature sensor. Refer to Component Parts Location.

Component Inspection

CHECK ENGINE OIL TEMPERATURE SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect engine oil temperature sensor harness connector.

  3. Remove engine oil temperature sensor. Refer to Component Parts Location.

  4. Check resistance between engine oil temperature sensor terminals by heating with hot water as shown in the figure.

    TerminalsConditionResistance (kΩ)
    3 and 1 Temperature [°C (°F)] 20 (68) 2.37 - 2.63
    50 (122) 0.68 - 1.00
    90 (194) 0.236 - 0.260

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace engine oil temperature sensor. Refer to Component Parts Location.