P0850 Pnp Switch
DESCRIPTION
When the selector lever position is P or N, park/neutral position (PNP) signal from the transmission range switch is sent to ECM.
DTC DETECTION LOGIC
The signal of the park/neutral position (PNP) signal does not change during driving after the engine is started.
| DTC | CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | |
| P0850 | P-N POS SW/CIRCUIT (Park/Neutral switch input circuit) |
Diagnosis condition | — |
| Signal (terminal) | The park/neutral position (PNP) signal circuit | ||
| Threshold | The signal does not change during driving after the engine is started | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
Harness or connectors
[The park/neutral position (PNP) signal circuit is open or shorted.]
TCM
FAIL-SAFE
Not applicable
INSPECTION START
Will CONSULT be used?
Will CONSULT be used?
YES>>GO TO 2.
NO>>GO TO 5.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
GO TO 3.
CHECK PNP SIGNAL
With CONSULT
Turn ignition switch ON.
Select “P/N POSI SW” in “DATA MONITOR” mode with CONSULT. Then check the “P/N POSI SW” signal under the following conditions.
Position (Selector lever) Known-good signal N or P position ON Except above position OFF
Is the inspection result normal?
YES>>GO TO 4.
NO>>Proceed to Diagnosis Procedure.
PERFORM DTC CONFIRMATION PROCEDURE
Select “DATA MONITOR” mode with CONSULT.
Start engine and warm it up to normal operating temperature.
Maintain the following conditions for at least 50 consecutive seconds.
ENG SPEED 1,100 - 6,375 rpm COOLANT TEMP/S More than 65 °C B/FUEL SCHDL 2.2 - 31.8 msec VHCL SPEED SE More than 64 km/h Selector lever Suitable position Check 1st trip DTC.
Is 1st trip DTC detected?
YES>>Proceed to Diagnosis Procedure.
NO>>INSPECTION END
PERFORM COMPONENT FUNCTION CHECK
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals.
ECM Condition Voltage + – Connector Terminal Connector Terminal F79 83 E32 152 Selector lever position P or N Approx. 0 V Except above Battery voltage
Is the inspection result normal?
YES>>To check malfunction symptom before repair: Refer to Intermittent Incident.
YES>>Confirmation after repair: INSPECTION END
NO>>Proceed to Diagnosis Procedure.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY
Ignition switch OFF.
Disconnect transmission range switch harness connector.
Ignition switch ON.
Check the voltage between transmission range switch harness connector and ground.
+ − Voltage
(Approx.)Transmission range switch Connector Terminal F29 7 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY CIRCUIT
Ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between transmission range switch harness connector and IPDM E/R harness connector.
Transmission range switch IPDM E/R Continuity Connector Terminal Connector Terminal F29 7 F24 63 Yes Also check harness for short to ground.
Is the inspection result normal?
YES>>Perform the trouble diagnosis for power supply circuit.
NO>>Repair or replace error-detected parts.
CHECK TRANSMISSION RANGE SWITCH SIGNAL CIRCUIT
Ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between transmission range switch harness connector and ECM harness connector.
Transmission range switch ECM Continuity Connector Terminal Connector Terminal F29 10 F79 83 Yes Also check harness for short to ground and to power.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected parts.
CHECK TRANSMISSION RANGE SWITCH
Check the transmission range switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>INSPECTION END
NO>>There is malfunction of transmission range switch. Replace transmission range switch. Refer to Removal and Installation.