Engine

P1564 Ascd Steering Switch

27steps
~162min
4/5difficulty
Done 0 of 27
DTC Description

DTC DETECTION LOGIC

  1. An excessively high voltage signal from the ASCD steering switch is sent to ECM.

  2. ECM detects that input signal from the ASCD steering switch is out of the specified range.

  3. ECM detects that the ASCD steering switch is stuck ON.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1564

ASCD SW

(ASCD steering switch)
1 Diagnosis condition —
Signal (terminal) ASCD steering switch signal
Threshold An excessively high voltage signal from the ASCD steering switch is sent to ECM
Diagnosis delay time —
2 Diagnosis condition —
Signal (terminal) ASCD steering switch signal
Threshold ECM detects that input signal from the ASCD steering switch is out of the specified range
Diagnosis delay time —
3 Diagnosis condition —
Signal (terminal) ASCD steering switch signal
Threshold ECM detects that the ASCD steering switch is stuck ON
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (The switch circuit is open or shorted.)

  • ASCD steering switch

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with DTC P0605, first perform the confirmation procedure for DTC P0605.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.

  3. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.

  4. Press RES+ switch for at least 10 seconds, then release it and wait at least 10 seconds.

  5. Press SET- switch for at least 10 seconds, then release it and wait at least 10 seconds.

  6. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with DTC P0605, first perform the confirmation procedure for DTC P0605.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ASCD STEERING SWITCH CIRCUIT

With CONSULT

  1. Turn ignition switch ON.

  2. Select “MAIN SW”, “CANCEL SW”, “RESUME/ACC SW” and “SET SW” in “DATA MONITOR” mode with CONSULT.

  3. Check each item indication under the following conditions.

    Monitor itemConditionIndication
    MAIN SW ON/OFF (MAIN) switch Pressed ON
    Released OFF
    CANCEL SW CANCEL switch Pressed ON
    Released OFF
    RESUME/ACC SW RES+ switch Pressed ON
    Released OFF
    SET SW SET- switch Pressed ON
    Released OFF

Without CONSULT

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connector terminals under the following conditions.

    ECMConditionVoltage (V)
    Connector+–
    TerminalTerminal
    E32 134 135 ON/OFF (MAIN) switch: Pressed Approx. 0
    CANCEL switch: Pressed Approx. 1
    SET- switch: Pressed Approx. 2
    RES+ switch: Pressed Approx. 3
    All ASCD steering switches: Released Approx. 4

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 3.

CHECK ASCD STEERING SWITCH GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect combination switch harness connector M143.

  4. Check the continuity between combination switch and ECM harness connector.

    Combination switchECMContinuity
    TerminalConnectorTerminal
    35 E32 135 Existed
  5. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT

  1. Check the continuity between combination switch and ECM harness connector.

    Combination switchECMContinuity
    TerminalConnectorTerminal
    34 E32 134 Existed
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH

Check ASCD steering switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace ASCD steering switch. Refer to Removal and Installation.

Component Inspection

CHECK ASCD STEERING SWITCH

  1. Turn ignition switch OFF.

  2. Disconnect combination switch (spiral cable) harness connector.

  3. Check resistance between combination switch harness connector terminals as per the following.

    Combination switchConditionResistance (Ω)
    ConnectorTerminals
    M143 34 and 35 ON/OFF (MAIN) switch: Pressed Approx. 0
    CANCEL switch: Pressed Approx. 250
    SET- switch: Pressed Approx. 660
    RES+ switch: Pressed Approx. 1,480
    All ASCD steering switches: Released Approx. 4,000

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace ASCD steering switch. Refer to Removal and Installation.