Engine

P0053 A/f Sensor 1 Heater

19steps
~114min
4/5difficulty
Done 0 of 19
DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0053

HO2S1 HTR B1

(HO2S heater resistance bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 heater (bank 1) signal
Threshold During engine running, weighted average of A/F sensor internal resistance is out of the normal range
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors [A/F sensor 1 (bank 1) heater circuit is open or shorted.]

  • A/F sensor 1 (bank 1) heater

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P0053 is displayed with DTC 0031, 0032 or P0130, first perform the confirmation procedure (trouble diagnosis) for DTC 0031, 0032 or P0130.

Is DTC P0031, P0032 or P0130 detected?

YES>>

Perform diagnosis of applicable.

  • P0130: Refer to DTC Description.

  • P0031: Refer to DTC Description.

  • P0032: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

When DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and warm it up until the engine coolant temperature reaches 25 °C or more.

  2. Keep the engine at idle at least 35 seconds.

  3. Check 1st trip DTC.

Is DTC P0053 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0053 is displayed with DTC 0031, 0032 or P0130, first perform the confirmation procedure (trouble diagnosis) for DTC 0031, 0032 or P0130.

Is DTC P0031, P0032 or P0130 detected?

YES>>

Perform diagnosis of applicable.

  • P0130: Refer to DTC Description.

  • P0031: Refer to DTC Description.

  • P0032: Refer to DTC Description.

NO>>

GO TO 2.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between A/F sensor 1 harness connector and ground.

    +−Voltage
    A/F sensor 1
    ConnectorTerminal
    F12 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

A/F sensor 1IPDM E/RContinuity
ConnectorTerminalConnectorTerminal
F12 1 F19 52 Existed

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check harness continuity between A/F sensor 1 harness connector and ECM harness connector.

    A/F sensor 1ECMContinuity
    ConnectorTerminalConnectorTerminal
    F12 2 F78 6 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK A/F SENSOR 1 HEATER

Check A/F sensor 1 heater. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

Component Inspection

CHECK AIR FUEL RATIO (A/F) SENSOR 1

  1. Turn ignition switch OFF.

  2. Disconnect A/F sensor 1 harness connector.

  3. Check resistance between A/F sensor 1 terminals as per the following.

    +−Resistance
    A/F sensor 1
    Terminal
    2 1 1.8 - 2.44 Ω [at 25 °C]
    3

    ∞Ω

    (Continuity should not exist)
    4
    1 3
    4

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).