Engine

P014c A/f Sensor 1

40steps
~240min
4/5difficulty
Done 0 of 40
DTC Description

DTC DETECTION LOGIC

To judge malfunctions, this diagnosis measures response time of the A/F signal computed by ECM from the A/F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel feedback control constant, and the A/F sensor 1 temperature index. Judgment is based on whether the compensated time (the A/F signal cycling time index) is inordinately long or not.

The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P014C

A/F SENSOR1 (B1)

(O2 sensor slow response - rich to lean bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P014D

A/F SENSOR1 (B1)

(O2 sensor slow response - lean to rich bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P014E

A/F SENSOR1 (B2)

(O2 sensor slow response - rich to lean bank 2 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P014F

A/F SENSOR1 (B2)

(O2 sensor slow response - lean to rich bank 2 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P015A

A/F SENSOR1 (B1)

(O2 sensor delayed response - rich to lean bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P015B

A/F SENSOR1 (B1)

(O2 sensor delayed response - lean to rich bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P015C

A/F SENSOR1 (B2)

(O2 sensor delayed response - rich to lean bank 2 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —
P015D

A/F SENSOR1 (B2)

(O2 sensor delayed response - lean to rich bank 2 sensor 1)
Diagnosis condition —
Signal (terminal) A/F sensor 1 signal
Threshold The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM
Diagnosis delay time —

POSSIBLE CAUSE

P014C

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P014D

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P014E

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P014F

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P015A

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P015B

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P015C

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P015D

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

Do you have CONSULT?

YES>>

GO TO 2.

NO>>

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE-1

With CONSULT

  1. Start engine and warm it up to normal operating temperature.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no load.

  6. Let engine idle for 1 minute.

  7. Increase the engine speed up to about 3,600 rpm and keep it for 10 seconds.

  8. Fully release accelerator pedal and then let engine idle for about 1 minute.

  9. Check the items status of “DATA MONITOR” as follows.

    DTCData monitor itemStatus
    • P014C

    • P014D

    • P015A

    • P015B

    A/F SEN1 DIAG3 (B1) PRSNT
    • P014E

    • P014F

    • P015C

    • P015D

    A/F SEN1 DIAG3 (B2)

Is “PRSNT” displayed on CONSULT screen?

YES>>

GO TO 4.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

Perform DTC confirmation procedure-1 again.

Is “PRSNT” displayed on CONSULT screen?

YES>>

GO TO 4.

NO>>

Refer to Component Function Check.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

  1. Wait for about 20 seconds at idle.

  2. Check the items status of “DATA MONITOR” as follows.

    DTCData monitor itemStatus
    • P014C

    • P014D

    • P015A

    • P015B

    A/F SEN1 DIAG1 (B1) CMPLT
    A/F SEN1 DIAG2 (B1)
    • P014E

    • P014F

    • P015C

    • P015D

    A/F SEN1 DIAG1 (B2)
    A/F SEN1 DIAG2 (B2)

Is “CMPLT” displayed on CONSULT screen?

YES>>

GO TO 5.

NO>>

Refer to Component Function Check.

PERFORM SELF-DIAGNOSIS

With CONSULT

Check the “SELF-DIAG RESULT”.

Is any DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

CHECK AIR-FUEL RATIO SELF-LEARNING VALUE

With GST

  1. Start engine and warm it up to normal operating temperature.

  2. Select Service $01 with GST.

  3. Calculate the total value of “Short term fuel trim” and “Long term fuel trim” indications.

Is the total percentage within ±15%?

YES>>

GO TO 8.

NO>>

GO TO 7.

DETECT MALFUNCTIONING PART

Check the following.

  • Intake air leaks

  • Exhaust gas leaks

  • Incorrect fuel pressure

  • Lack of fuel

  • Fuel injector

  • Incorrect PCV hose connection

  • PCV valve

  • Mass air flow sensor

>>

Repair or replace malfunctioning part.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.

  5. Let engine idle for 1 minute.

  6. Increase the engine speed up to about 3,600 rpm and keep it for 10 seconds.

  7. Fully release accelerator pedal and then let engine idle for about 1 minute.

  8. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

RETIGHTEN A/F SENSOR 1

Loosen and retighten the A/F sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

>>

GO TO 2.

CHECK EXHAUST GAS LEAK

  1. Start engine and run it at idle.

  2. Listen for an exhaust gas leak before three way catalyst 1.

Is exhaust gas leak detected?

YES>>

Repair or replace.

NO>>

GO TO 3.

CHECK FOR INTAKE AIR LEAK

Listen for an intake air leak after the mass air flow sensor.

Is intake air leak detected?

YES>>

Repair or replace.

NO>>

GO TO 4.

CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE

  1. Clear the mixture ratio self-learning value. Refer to Description.

  2. Run engine for at least 10 minutes at idle speed.

Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected? Is it difficult to start engine?

YES>>

Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. Refer to DTC Description or DTC Description.

NO>>

GO TO 5.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Disconnect A/F sensor 1 harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between A/F sensor 1 harness connector and ground.

    DTCA/F sensor 1GroundVoltage
    BankConnectorTerminal
    • P014C

    • P014D

    • P015A

    • P015B

    1 F12 1 Ground Battery voltage
    • P014E

    • P014F

    • P015C

    • P015D

    2 F61 1

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

DTCA/F sensor 1IPDM E/RContinuity
BankConnectorTerminalConnectorTerminal
  • P014C

  • P014D

  • P015A

  • P015B

1 F12 1 F19 52 Existed
  • P014E

  • P014F

  • P015C

  • P015D

2 F61 1 53

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

    DTCA/F sensor 1ECMContinuity
    BankConnectorTerminalConnectorTerminal
    • P014C

    • P014D

    • P015A

    • P015B

    1 F12 3 F79 66 Existed
    4 67
    • P014E

    • P014F

    • P015C

    • P015D

    2 F61 3 76
    4 77
  4. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

    DTCA/F sensor 1GroundContinuity
    BankConnectorTerminal
    • P014C

    • P014D

    • P015A

    • P015B

    1 F12 3 Ground Not existed
    4
    • P014E

    • P014F

    • P015C

    • P015D

    2 F61 3
    4
    DTCECMGroundContinuity
    BankConnectorTerminal
    • P014C

    • P014D

    • P015A

    • P015B

    1 F79 66 Ground Not existed
    67
    • P014E

    • P014F

    • P015C

    • P015D

    2 76
    77
  5. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER

Check air fuel ratio (A/F) sensor 1 heater. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

CHECK MASS AIR FLOW SENSOR

Check both mass air flow sensor (bank 1 and bank 2). Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace malfunctioning mass air flow sensor. Refer to Removal and Installation.

CHECK PCV VALVE

Check PCV valve. Refer to Work Procedure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace PCV valve. Refer to Component Parts Location.