Engine

P1805 Brake Switch

16steps
~96min
4/5difficulty
Done 0 of 16
DTC Description

DESCRIPTION

Brake switch signal is applied to the ECM via the stop lamp switch when the brake pedal is depressed. This signal is used mainly to decrease the engine speed when the Nissan Murano vehicle is driven.

DTC DETECTION LOGIC

A brake switch signal is not sent to ECM for extremely long time while the vehicle is driving.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1805

BRAKE SW/CIRCUIT

(Stop lamp switch circuit)
Diagnosis condition —
Signal (terminal) Stop lamp switch signal
Threshold A brake switch signal is not sent to ECM while the Nissan Murano vehicle is driving
Diagnosis delay time Extremely long time

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open or shorted.)

  • Stop lamp switch

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Brake switch

ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.

Therefore, acceleration will be poor.
Nissan Murano Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Fully depress the brake pedal for at least 5 seconds.

  3. Erase the DTC with CONSULT.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Go to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK STOP LAMP SWITCH CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the stop lamp when depressing and releasing the brake pedal.

    Brake pedalStop lamp
    Fully released Not illuminated
    Slightly depressed Illuminated

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-I

  1. Turn ignition switch OFF.

  2. Remove stop lamp switch.

  3. Check the voltage between stop lamp switch harness connector and ground.

    +−Voltage
    Stop lamp switch
    ConnectorTerminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-II

  1. Check the continuity between stop lamp switch harness connector and ECM harness connector.

    Stop lamp switchECMContinuity
    ConnectorTerminalConnectorTerminal
    E38 2 E32 139 Existed
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to Component Inspection (Stop Lamp Switch) .

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace stop lamp switch. Refer to Removal and Installation.

Component Inspection (Stop Lamp Switch)

CHECK STOP LAMP SWITCH-I

  1. Turn ignition switch OFF.

  2. Disconnect stop lamp switch harness connector.

  3. Check harness continuity between stop lamp switch terminals under the following conditions.

    TerminalsConditionContinuity
    1 and 2 Brake pedal Fully released Not existed
    Slightly depressed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH-II

  1. Adjust stop lamp switch installation. Refer to Adjustment.

  2. Check harness continuity between stop lamp switch terminals under the following conditions.

    TerminalsConditionContinuity
    1 and 2 Brake pedal Fully released Not existed
    Slightly depressed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace stop lamp switch. Refer to Removal and Installation.