P1572 Ascd Brake Switch
DESCRIPTION
When the brake pedal is depressed, brake pedal position switch is turned OFF and stop lamp switch is turned ON. ECM detects the state of the brake pedal by this input of two kinds (ON/OFF signal).
Refer to System Description for the ASCD function.
DTC DETECTION LOGIC
When the vehicle speed is above 30 km/h, ON signals from the stop lamp switch and the brake pedal position switch are sent to the ECM at the same time.
Brake pedal position switch signal is not sent to ECM for extremely long time while the Nissan Murano vehicle is driving.
| DTC | CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | ||
| P1572 | ASCD BRAKE SW (Brake pedal position switch) |
1 | Diagnosis condition | — |
| Signal (terminal) |
|
|||
| Threshold | When the Nissan Murano vehicle speed is above 30 km/h, ON signals from the stop lamp switch and the brake pedal position switch are sent to the ECM at the same time | |||
| Diagnosis delay time | — | |||
| 2 | Diagnosis condition | — | ||
| Signal (terminal) | Brake pedal position switch signal | |||
| Threshold | Brake pedal position switch signal is not sent to ECM for extremely long time while the Nissan Murano vehicle is driving | |||
| Diagnosis delay time | Extremely long time | |||
POSSIBLE CAUSE
DTC P1572 - 1
Harness or connectors
(The stop lamp switch circuit is shorted.)
Harness or connectors
(The brake pedal position switch circuit is shorted.)
Stop lamp switch
Brake pedal position switch
Incorrect stop lamp switch installation
Incorrect brake pedal position switch installation
ECM
DTC P1572 - 2
Harness or connectors
(The stop lamp switch circuit is shorted.)
Harness or connectors
(The brake pedal position switch circuit is shorted.)
Stop lamp switch
Brake pedal position switch
Incorrect stop lamp switch installation
Incorrect brake pedal position switch installation
ECM
FAIL-SAFE
Not applicable
CHECK DTC PRIORITY
If DTC P1572 is displayed with DTC P0605, first perform the confirmation procedure for DTC P0605.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Description.
NO>>GO TO 2.
INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES>>GO TO 3.
NO>>GO TO 6.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>GO TO 4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION 1-I
Start engine (VDC switch OFF).
Select “DATA MONITOR” mode with CONSULT.
Press MAIN switch and make sure that CRUISE lamp lights up.
Drive the Nissan Murano vehicle for at least 5 consecutive seconds under the following conditions.
VHCL SPEED SE More than 30 km/h Selector lever Suitable position Check 1st trip DTC.
Is 1st trip DTC detected?
YES>>Go to Diagnosis Procedure.
NO>>GO TO 5.
PERFORM DTC CONFIRMATION PROCEDURE 1-II
Drive the Nissan Murano vehicle for at least 5 consecutive seconds under the following conditions.
VHCL SPEED SE More than 30 km/h Selector lever Suitable position Driving location Depress the brake pedal for more than five seconds so as not to come off from the above-mentioned Nissan Murano vehicle speed. Check 1st trip DTC.
Is 1st trip DTC detected?
YES>>Go to Diagnosis Procedure.
NO>>INSPECTION END
PERFORM COMPONENT FUNCTION CHECK
Turn ignition switch ON.
Check the voltage between ECM harness connectors.
ECM Condition Voltage Connector + – Terminal Terminal E32 140 152 Brake pedal Slightly depressed Approx. 0 V Fully released Battery voltage
Is the inspection result normal?
YES>>To check malfunction symptom before repair: Refer to Intermittent Incident.
YES>>Confirmation after repair: INSPECTION END
NO>>GO TO 7.
PERFORM COMPONENT FUNCTION CHECK-II
Check the voltage between ECM harness connectors.
| ECM | Condition | Voltage | |||
|---|---|---|---|---|---|
| Connector | + | – | |||
| Terminal | Terminal | ||||
| E32 | 139 | 152 | Brake pedal | Slightly depressed | Battery voltage |
| Fully released | Approx. 0 V | ||||
Is the inspection result normal?
YES>>To check malfunction symptom before repair: Refer to Intermittent Incident.
YES>>Confirmation after repair: INSPECTION END
NO>>Go to Diagnosis Procedure.
CHECK DTC PRIORITY
If DTC P1572 is displayed with DTC P0605, first perform the confirmation procedure for DTC P0605.
Is applicable DTC detected?
YES>>Perform diagnosis of applicable. Refer to DTC Description.
NO>>GO TO 2.
CHECK OVERALL FUNCTION-I
With CONSULT
Turn ignition switch ON.
Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT.
Check “BRAKE SW1” indication under the following conditions.
Monitor item Condition Indication BRAKE SW1 Brake pedal Slightly depressed OFF Fully released ON
Without CONSULT
Turn ignition switch ON.
Check the voltage between ECM harness connectors.
ECM Condition Voltage Connector + – Terminal E32 140 152 Brake pedal Slightly depressed Approx. 0 V Fully released Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 4.
CHECK OVERALL FUNCTION-II
With CONSULT
Check “BRAKE SW2” indication in “DATA MONITOR” mode.
| Monitor item | Condition | Indication | |
|---|---|---|---|
| BRAKE SW2 | Brake pedal | Slightly depressed | ON |
| Fully released | OFF | ||
Without CONSULT
Check the voltage between ECM harness connectors.
| ECM | Condition | Voltage | |||
|---|---|---|---|---|---|
| Connector | + | – | |||
| Terminal | |||||
| E32 | 139 | 152 | Brake pedal | Slightly depressed | Battery voltage |
| Fully released | Approx. 0 V | ||||
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 7.
CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY
Turn ignition switch OFF.
Disconnect brake pedal position switch harness connector.
Turn ignition switch ON.
Check the voltage between brake pedal position switch harness connector and ground.
Brake pedal position switch Ground Voltage Connector Terminal E72 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace error-detected parts.
CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between brake pedal position switch harness connector and ECM harness connector.
Brake pedal position switch ECM Continuity Connector Terminal Connector Terminal E72 2 E32 140 Existed Also check harness for short to ground and short to power.
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair open circuit, short to ground or short to power in harness or connectors.
CHECK BRAKE PEDAL POSITION SWITCH
Check brake pedal position switch. Refer to Component Inspection (Brake Pedal Position Switch) .
Is the inspection result normal?
YES>>GO TO 7.
NO>>Replace brake pedal position switch. Refer to Removal and Installation.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to Component Inspection (Stop Lamp Switch) .
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace stop lamp switch. Refer to Removal and Installation.
CHECK BRAKE PEDAL POSITION SWITCH-I
Turn ignition switch OFF.
Disconnect brake pedal position switch harness connector.
Check the continuity between brake pedal position switch terminals under the following conditions.
Terminals Condition Continuity 1 and 2 Brake pedal Fully released Existed Slightly depressed Not existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 2.
CHECK BRAKE PEDAL POSITION SWITCH-II
Adjust brake pedal position switch installation. Refer to Adjustment.
Check the continuity between brake pedal position switch terminals under the following conditions.
Terminals Condition Continuity 1 and 2 Brake pedal Fully released Existed Slightly depressed Not existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace brake pedal position switch. Refer to Removal and Installation.
CHECK STOP LAMP SWITCH-I
Turn ignition switch OFF.
Disconnect stop lamp switch harness connector.
Check harness continuity between stop lamp switch terminals under the following conditions.
Terminals Condition Continuity 1 and 2 Brake pedal Fully released Not existed Slightly depressed Existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>GO TO 2.
CHECK STOP LAMP SWITCH-II
Adjust stop lamp switch installation. Refer to Adjustment.
Check harness continuity between stop lamp switch terminals under the following conditions.
Terminals Condition Continuity 1 and 2 Brake pedal Fully released Not existed Slightly depressed Existed
Is the inspection result normal?
YES>>INSPECTION END
NO>>Replace stop lamp switch. Refer to Removal and Installation.