Engine

P0078 Evt Control Solenoid Valve

22steps
~132min
5/5difficulty
Done 0 of 22
DTC Description

DTC DETECTION LOGIC

An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0078

EX V/T ACT/CIRC-B1

[Exhaust valve timing control solenoid valve (bank 1) circuit]
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from exhaust valve timing control solenoid valve to ECM
Threshold An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve
Diagnosis delay time —
P0084

EX V/T ACT/CIRC-B2

[Exhaust valve timing control solenoid valve (bank 2) circuit]
Diagnosis condition Start engine and let it idle
Signal (terminal) Voltage signal transmitted from exhaust valve timing control solenoid valve to ECM
Threshold An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve
Diagnosis delay time —

POSSIBLE CAUSE

P0078

  • Harness or connectors (Exhaust valve timing control solenoid valve circuit is open or shorted.)

  • Exhaust valve timing control solenoid valve

P0084

  • Harness or connectors (Exhaust valve timing control solenoid valve circuit is open or shorted.)

  • Exhaust valve timing control solenoid valve

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle for 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT - 1

  1. Turn ignition switch OFF.

  2. Disconnect exhaust valve timing control solenoid valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between exhaust valve timing control solenoid valve harness connector and ground.

    DTC+−Voltage
    Exhaust valve timing control solenoid valve
    BankConnectorTerminal
    P0078 1 F72 1 Ground Battery voltage
    P0084 2 F73 1

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK EVT CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust valve timing control solenoid valve harness connector and ECM harness connector.

    DTC+−Continuity
    Exhaust valve timing control solenoid valveECM
    BankConnectorTerminalConnectorTerminal
    P0078 1 F72 2 F79 58 Existed
    P0084 2 F73 2 60
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE

Check exhaust valve timing control solenoid valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT - 2

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and exhaust valve timing control solenoid valve harness connector.

    DTC+−Continuity
    IPDM E/RExhaust valve timing control solenoid valve
    ConnectorTerminalConnectorTerminal
    P0075 F19 59 F72 1 Existed
    P0081 F73 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

Component Inspection

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE - 1

  1. Turn ignition switch OFF.

  2. Disconnect exhaust valve timing control solenoid valve harness connector.

  3. Check resistance between exhaust valve timing control solenoid valve terminals as follows.

    Exhaust valve timing control solenoid valve

    Condition

    Resistance
    +−
    Terminal
    2 1 Temperature 20 °C 7.0 – 7.8 Ω
    1 Ground

    ∞

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE - 2

  1. Remove exhaust valve timing control solenoid valve. Refer to Exploded View.

  2. Apply 12 V between exhaust valve timing control solenoid valve terminals 1 and 2, and then interrupt it. Check that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.