Engine

P2138 App Sensor

25steps
~150min
4/5difficulty
Done 0 of 25
DTC Description

DTC DETECTION LOGIC

Rationally incorrect voltage is sent to ECM compared with the signals from APP sensor 1 and APP sensor 2.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2138

APP SENSOR

(Throttle/Pedal position sensor/switch “D” / “E” voltage correlation)
Diagnosis condition Start engine and let it idle
Signal (terminal) APP sensor 1 signal and APP sensor 2 signal
Threshold Rationally incorrect voltage is sent to ECM compared with the signals from APP sensor 1 and APP sensor 2
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connector

    (APP sensor 1 or 2 circuit is open or shorted.)

    [CMP sensor (PHASE) circuit is open or shorted.]

    (EOP sensor circuit is shorted.)

    (Refrigerant pressure sensor is shorted.)

  • Accelerator pedal position sensor

    (APP sensor 1 or 2)

  • Camshaft position sensor (PHASE)

  • Engine oil pressure sensor

  • Refrigerant pressure sensor

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Accelerator pedal position sensor

The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 degrees.

The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.

Therefore, the acceleration will be poor.
DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK APP SENSOR 1 POWER SUPPLY

  1. Disconnect accelerator pedal position (APP) sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between APP sensor harness connector and ground.

    +−

    Voltage

    (Approx.)
    APP sensor
    ConnectorTerminal
    E31 4 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between APP sensor harness connector and ECM harness connector.

    APP sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E31 4 E32 146 Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

CHECK APP SENSOR 2 POWER SUPPLY

  1. Turn ignition switch ON.

  2. Check the voltage between APP sensor harness connector and ground.

    +−

    Voltage

    (Approx.)
    APP sensor
    ConnectorTerminal
    E31 5 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between APP sensor harness connector and ECM harness connector.

    APP sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E31 5 E32 142 Existed

Is the inspection result normal?

YES>>

Check sensor power supply 2 circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK APP SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between APP sensor harness connector and ECM harness connector.

    APP sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E31 1 E32 144 Existed
    2 151
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK APP SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between APP sensor harness connector and ECM harness connector.

    APP sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E31 3 E32 150 Existed
    6 143
  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK APP SENSOR

Check APP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace accelerator pedal assembly. Refer to Removal and Installation.

Component Inspection

CHECK ACCELERATOR PEDAL POSITION SENSOR

  1. Reconnect all harness connectors disconnected.

  2. Turn ignition switch ON.

  3. Check the voltage between ECM harness connector terminals under the following conditions.

    ECMConditionVoltage (V)
    Connector+–
    Terminal
    E32 143 144 Accelerator pedal Fully released 0.25 - 0.50
    Fully depressed 2.0 - 2.5
    150 151 Fully released 0.5 - 1.0
    Fully depressed 4.2 - 4.8

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace accelerator pedal assembly. Refer to Removal and Installation.